#include <inttypes.h>
#include <glib.h>
#include <libusb.h>
+#include <sigrok.h>
#include "config.h"
-#include "sigrok.h"
#define USB_VENDOR 0x0925
#define USB_PRODUCT 0x3881
#define NUM_PROBES 8
#define NUM_TRIGGER_STAGES 4
#define TRIGGER_TYPES "01"
-#define FIRMWARE FIRMWARE_DIR "/saleae-logic.firmware"
+#define FIRMWARE FIRMWARE_DIR "/saleae-logic.fw"
/* delay in ms */
#define FIRMWARE_RENUM_DELAY 2000
#define NUM_SIMUL_TRANSFERS 10
#define MAX_EMPTY_TRANSFERS (NUM_SIMUL_TRANSFERS * 2)
-/* software trigger implementation: positive values indicate trigger stage */
+/* Software trigger implementation: positive values indicate trigger stage. */
#define TRIGGER_FIRED -1
/* There is only one model Saleae Logic, and this is what it supports: */
static uint8_t trigger_mask[NUM_TRIGGER_STAGES] = { 0 };
static uint8_t trigger_value[NUM_TRIGGER_STAGES] = { 0 };
static uint8_t trigger_buffer[NUM_TRIGGER_STAGES] = { 0 };
+
int trigger_stage = TRIGGER_FIRED;
static int hw_set_configuration(int device_index, int capability, void *value);
+static void hw_stop_acquisition(int device_index, gpointer session_device_id);
-/* returns 1 if the device's configuration profile match the Logic firmware's
- * configuration, 0 otherwise
+/*
+ * Returns 1 if the device's configuration profile match the Logic firmware's
+ * configuration, 0 otherwise.
*/
int check_conf_profile(libusb_device *dev)
{
sdi->status = ST_INACTIVE;
}
-static int configure_probes(GSList * probes)
+static int configure_probes(GSList *probes)
{
struct probe *probe;
GSList *l;
* or uploading the firmware again.
*/
if (upload_firmware(devlist[i]) > 0)
- g_warning("firmware upload failed for device %d", devcnt);
+ g_warning("firmware upload failed for "
+ "device %d", devcnt);
sdi->usb = usb_device_instance_new
- (libusb_get_bus_number(devlist[i]), 0, NULL);
+ (libusb_get_bus_number(devlist[i]), 0, NULL);
} else {
/* Already has the firmware, so fix the new address. */
sdi->usb = usb_device_instance_new
(libusb_get_bus_number(devlist[i]),
- libusb_get_device_address(devlist[i]),
- NULL);
+ libusb_get_device_address(devlist[i]), NULL);
}
devcnt++;
}
if (cur_samplerate == 0) {
/* Samplerate hasn't been set; default to the slowest one. */
if (hw_set_configuration(device_index, HWCAP_SAMPLERATE,
- &supported_samplerates[0]) == SIGROK_ERR)
+ &supported_samplerates[0]) == SIGROK_ERR)
return SIGROK_ERR;
}
if (supported_samplerates[i] == 0)
return SIGROK_ERR_SAMPLERATE;
- divider = (uint8_t) (48 / (float)(samplerate / 1000000)) - 1;
+ divider = (uint8_t) (48 / (samplerate / 1000000.0)) - 1;
g_message("setting samplerate to %" PRIu64 " Hz (divider %d)",
samplerate, divider);
* transfer that come in.
*/
if (num_samples == -1) {
- libusb_free_transfer(transfer);
+ if (transfer)
+ libusb_free_transfer(transfer);
return;
}
* The FX2 gave up. End the acquisition, the frontend
* will work out that the samplecount is short.
*/
- packet.type = DF_END;
- session_bus(user_data, &packet);
- num_samples = -1;
+ hw_stop_acquisition(-1, user_data);
}
return;
} else {
num_samples += cur_buflen;
if ((unsigned int)num_samples > limit_samples) {
- /* End the acquisition. */
- packet.type = DF_END;
- session_bus(user_data, &packet);
- num_samples = -1;
+ hw_stop_acquisition(-1, user_data);
}
} else {
/*
lupfd = libusb_get_pollfds(usb_context);
for (i = 0; lupfd[i]; i++)
- source_add(lupfd[i]->fd, lupfd[i]->events, -1, receive_data,
+ source_add(lupfd[i]->fd, lupfd[i]->events, 40, receive_data,
NULL);
free(lupfd);