#include <inttypes.h>
#include <glib.h>
#include <libusb.h>
+#include <sigrok.h>
#include "config.h"
-#include "sigrok.h"
#define USB_VENDOR 0x0925
#define USB_PRODUCT 0x3881
#define NUM_PROBES 8
#define NUM_TRIGGER_STAGES 4
#define TRIGGER_TYPES "01"
-#define FIRMWARE FIRMWARE_DIR "/saleae-logic.firmware"
+#define FIRMWARE FIRMWARE_DIR "/saleae-logic.fw"
/* delay in ms */
#define FIRMWARE_RENUM_DELAY 2000
int trigger_stage = TRIGGER_FIRED;
static int hw_set_configuration(int device_index, int capability, void *value);
+static void hw_stop_acquisition(int device_index, gpointer session_device_id);
-/*
- * Returns 1 if the device's configuration profile match the Logic firmware's
- * configuration, 0 otherwise.
+/**
+ * Check the USB configuration to determine if this is a Saleae Logic.
+ *
+ * @return 1 if the device's configuration profile match the Logic firmware's
+ * configuration, 0 otherwise.
*/
int check_conf_profile(libusb_device *dev)
{
static int opendev2(int device_index, struct sigrok_device_instance **sdi,
libusb_device *dev, struct libusb_device_descriptor *des,
- int *skip)
+ int *skip, uint16_t vid, uint16_t pid, int interface)
{
int err;
return -1;
}
- if (des->idVendor != USB_VENDOR || des->idProduct != USB_PRODUCT)
+ if (des->idVendor != vid || des->idProduct != pid)
return 0;
if (*skip != device_index) {
(*sdi)->status = ST_ACTIVE;
g_message("opened device %d on %d.%d interface %d",
(*sdi)->index, (*sdi)->usb->bus,
- (*sdi)->usb->address, USB_INTERFACE);
+ (*sdi)->usb->address, interface);
} else {
g_warning("failed to open device: %d", err);
*sdi = NULL;
}
static int opendev3(struct sigrok_device_instance **sdi, libusb_device *dev,
- struct libusb_device_descriptor *des)
+ struct libusb_device_descriptor *des,
+ uint16_t vid, uint16_t pid, int interface)
{
int err;
return -1;
}
- if (des->idVendor != USB_VENDOR || des->idProduct != USB_PRODUCT)
+ if (des->idVendor != vid || des->idProduct != pid)
return 0;
if (libusb_get_bus_number(dev) == (*sdi)->usb->bus
(*sdi)->status = ST_ACTIVE;
g_message("opened device %d on %d.%d interface %d",
(*sdi)->index, (*sdi)->usb->bus,
- (*sdi)->usb->address, USB_INTERFACE);
+ (*sdi)->usb->address, interface);
} else {
g_warning("failed to open device: %d", err);
*sdi = NULL;
for (i = 0; devlist[i]; i++) {
/* TODO: Error handling. */
err = opendev2(device_index, &sdi, devlist[i], &des,
- &skip);
+ &skip, USB_VENDOR, USB_PRODUCT,
+ USB_INTERFACE);
}
} else if (sdi->status == ST_INACTIVE) {
/*
libusb_get_device_list(usb_context, &devlist);
for (i = 0; devlist[i]; i++) {
/* TODO: Error handling. */
- err = opendev3(&sdi, devlist[i], &des);
+ err = opendev3(&sdi, devlist[i], &des, USB_VENDOR,
+ USB_PRODUCT, USB_INTERFACE);
}
} else {
/* Status must be ST_ACTIVE, i.e. already in use... */
if (supported_samplerates[i] == 0)
return SIGROK_ERR_SAMPLERATE;
- divider = (uint8_t) (48 / (float)(samplerate / 1000000)) - 1;
+ divider = (uint8_t) (48 / (samplerate / 1000000.0)) - 1;
g_message("setting samplerate to %" PRIu64 " Hz (divider %d)",
samplerate, divider);
* transfer that come in.
*/
if (num_samples == -1) {
- libusb_free_transfer(transfer);
+ if (transfer)
+ libusb_free_transfer(transfer);
return;
}
* The FX2 gave up. End the acquisition, the frontend
* will work out that the samplecount is short.
*/
- packet.type = DF_END;
- session_bus(user_data, &packet);
- num_samples = -1;
+ hw_stop_acquisition(-1, user_data);
}
return;
} else {
num_samples += cur_buflen;
if ((unsigned int)num_samples > limit_samples) {
- /* End the acquisition. */
- packet.type = DF_END;
- session_bus(user_data, &packet);
- num_samples = -1;
+ hw_stop_acquisition(-1, user_data);
}
} else {
/*
lupfd = libusb_get_pollfds(usb_context);
for (i = 0; lupfd[i]; i++)
- source_add(lupfd[i]->fd, lupfd[i]->events, -1, receive_data,
+ source_add(lupfd[i]->fd, lupfd[i]->events, 40, receive_data,
NULL);
free(lupfd);