## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
##
-#
# I2C protocol decoder
-#
-
-#
-# The Inter-Integrated Circuit (I2C) bus is a bidirectional, multi-master
-# bus using two signals (SCL = serial clock line, SDA = serial data line).
-#
-# There can be many devices on the same bus. Each device can potentially be
-# master or slave (and that can change during runtime). Both slave and master
-# can potentially play the transmitter or receiver role (this can also
-# change at runtime).
-#
-# Possible maximum data rates:
-# - Standard mode: 100 kbit/s
-# - Fast mode: 400 kbit/s
-# - Fast-mode Plus: 1 Mbit/s
-# - High-speed mode: 3.4 Mbit/s
-#
-# START condition (S): SDA = falling, SCL = high
-# Repeated START condition (Sr): same as S
-# Data bit sampling: SCL = rising
-# STOP condition (P): SDA = rising, SCL = high
-#
-# All data bytes on SDA are exactly 8 bits long (transmitted MSB-first).
-# Each byte has to be followed by a 9th ACK/NACK bit. If that bit is low,
-# that indicates an ACK, if it's high that indicates a NACK.
-#
-# After the first START condition, a master sends the device address of the
-# slave it wants to talk to. Slave addresses are 7 bits long (MSB-first).
-# After those 7 bits, a data direction bit is sent. If the bit is low that
-# indicates a WRITE operation, if it's high that indicates a READ operation.
-#
-# Later an optional 10bit slave addressing scheme was added.
-#
-# Documentation:
-# http://www.nxp.com/acrobat/literature/9398/39340011.pdf (v2.1 spec)
-# http://www.nxp.com/acrobat/usermanuals/UM10204_3.pdf (v3 spec)
-# http://en.wikipedia.org/wiki/I2C
-#
# TODO: Look into arbitration, collision detection, clock synchronisation, etc.
# TODO: Handle clock stretching.
# TODO: Handle multiple different I2C devices on same bus
# -> we need to decode multiple protocols at the same time.
-'''
-Protocol output format:
-
-I2C packet:
-[<i2c_command>, <data>, <ack_bit>]
-
-<i2c_command> is one of:
- - 'START' (START condition)
- - 'START REPEAT' (Repeated START)
- - 'ADDRESS READ' (Address, read)
- - 'ADDRESS WRITE' (Address, write)
- - 'DATA READ' (Data, read)
- - 'DATA WRITE' (Data, write)
- - 'STOP' (STOP condition)
-
-<data> is the data or address byte associated with the 'ADDRESS*' and 'DATA*'
-command. For 'START', 'START REPEAT' and 'STOP', this is None.
-
-<ack_bit> is either 'ACK' or 'NACK', but may also be None.
-'''
-
import sigrokdecode as srd
# Annotation feed formats
-ANN_SHIFTED = 0
+ANN_SHIFTED = 0
ANN_SHIFTED_SHORT = 1
-ANN_RAW = 2
+ANN_RAW = 2
# Values are verbose and short annotation, respectively.
-protocol = {
+proto = {
'START': ['START', 'S'],
'START REPEAT': ['START REPEAT', 'Sr'],
'STOP': ['STOP', 'P'],
'DATA WRITE': ['DATA WRITE', 'DW'],
}
-# States
-FIND_START = 0
-FIND_ADDRESS = 1
-FIND_DATA = 2
-
class Decoder(srd.Decoder):
api_version = 1
id = 'i2c'
name = 'I2C'
longname = 'Inter-Integrated Circuit'
- desc = 'I2C is a two-wire, multi-master, serial bus.'
- longdesc = '...'
+ desc = 'Two-wire, multi-master, serial bus.'
license = 'gplv2+'
inputs = ['logic']
outputs = ['i2c']
{'id': 'scl', 'name': 'SCL', 'desc': 'Serial clock line'},
{'id': 'sda', 'name': 'SDA', 'desc': 'Serial data line'},
]
+ optional_probes = []
options = {
'addressing': ['Slave addressing (in bits)', 7], # 7 or 10
}
self.databyte = 0
self.wr = -1
self.is_repeat_start = 0
- self.state = FIND_START
+ self.state = 'FIND START'
self.oldscl = None
self.oldsda = None
self.out_proto = self.add(srd.OUTPUT_PROTO, 'i2c')
self.out_ann = self.add(srd.OUTPUT_ANN, 'i2c')
+ def report(self):
+ pass
+
def is_start_condition(self, scl, sda):
# START condition (S): SDA = falling, SCL = high
if (self.oldsda == 1 and sda == 0) and scl == 1:
self.startsample = self.samplenum
cmd = 'START REPEAT' if (self.is_repeat_start == 1) else 'START'
- self.put(self.out_proto, [cmd, None, None])
- self.put(self.out_ann, [ANN_SHIFTED, [protocol[cmd][0]]])
- self.put(self.out_ann, [ANN_SHIFTED_SHORT, [protocol[cmd][1]]])
+ self.put(self.out_proto, [cmd, None])
+ self.put(self.out_ann, [ANN_SHIFTED, [proto[cmd][0]]])
+ self.put(self.out_ann, [ANN_SHIFTED_SHORT, [proto[cmd][1]]])
- self.state = FIND_ADDRESS
+ self.state = 'FIND ADDRESS'
self.bitcount = self.databyte = 0
self.is_repeat_start = 1
self.wr = -1
# Return if we haven't collected all 8 + 1 bits, yet.
self.bitcount += 1
- if self.bitcount != 9:
+ if self.bitcount != 8:
return
+ # We triggered on the ACK/NACK bit, but won't report that until later.
+ self.startsample -= 1
+
# Send raw output annotation before we start shifting out
- # read/write and ack/nack bits.
+ # read/write and ACK/NACK bits.
self.put(self.out_ann, [ANN_RAW, ['0x%.2x' % self.databyte]])
- # We received 8 address/data bits and the ACK/NACK bit.
- self.databyte >>= 1 # Shift out unwanted ACK/NACK bit here.
-
- if self.state == FIND_ADDRESS:
+ if self.state == 'FIND ADDRESS':
# The READ/WRITE bit is only in address bytes, not data bytes.
self.wr = 0 if (self.databyte & 1) else 1
d = self.databyte >> 1
- elif self.state == FIND_DATA:
+ elif self.state == 'FIND DATA':
d = self.databyte
- else:
- # TODO: Error?
- pass
- # Last bit that came in was the ACK/NACK bit (1 = NACK).
- ack_bit = 'NACK' if (sda == 1) else 'ACK'
-
- if self.state == FIND_ADDRESS and self.wr == 1:
+ if self.state == 'FIND ADDRESS' and self.wr == 1:
cmd = 'ADDRESS WRITE'
- elif self.state == FIND_ADDRESS and self.wr == 0:
+ elif self.state == 'FIND ADDRESS' and self.wr == 0:
cmd = 'ADDRESS READ'
- elif self.state == FIND_DATA and self.wr == 1:
+ elif self.state == 'FIND DATA' and self.wr == 1:
cmd = 'DATA WRITE'
- elif self.state == FIND_DATA and self.wr == 0:
+ elif self.state == 'FIND DATA' and self.wr == 0:
cmd = 'DATA READ'
- self.put(self.out_proto, [cmd, d, ack_bit])
- self.put(self.out_ann, [ANN_SHIFTED,
- [protocol[cmd][0], '0x%02x' % d, protocol[ack_bit][0]]])
- self.put(self.out_ann, [ANN_SHIFTED_SHORT,
- [protocol[cmd][1], '0x%02x' % d, protocol[ack_bit][1]]])
+ self.put(self.out_proto, [cmd, d])
+ self.put(self.out_ann, [ANN_SHIFTED, [proto[cmd][0], '0x%02x' % d]])
+ self.put(self.out_ann, [ANN_SHIFTED_SHORT, [proto[cmd][1], '0x%02x' % d]])
- self.bitcount = self.databyte = 0
+ # Done with this packet.
self.startsample = -1
+ self.bitcount = self.databyte = 0
+ self.state = 'FIND ACK'
- if self.state == FIND_ADDRESS:
- self.state = FIND_DATA
- elif self.state == FIND_DATA:
- # There could be multiple data bytes in a row.
- # So, either find a STOP condition or another data byte next.
- pass
+ def get_ack(self, scl, sda):
+ self.startsample = self.samplenum
+ ack_bit = 'NACK' if (sda == 1) else 'ACK'
+ self.put(self.out_proto, [ack_bit, None])
+ self.put(self.out_ann, [ANN_SHIFTED, [proto[ack_bit][0]]])
+ self.put(self.out_ann, [ANN_SHIFTED_SHORT, [proto[ack_bit][1]]])
+ # There could be multiple data bytes in a row, so either find
+ # another data byte or a STOP condition next.
+ self.state = 'FIND DATA'
def found_stop(self, scl, sda):
self.startsample = self.samplenum
+ self.put(self.out_proto, ['STOP', None])
+ self.put(self.out_ann, [ANN_SHIFTED, [proto['STOP'][0]]])
+ self.put(self.out_ann, [ANN_SHIFTED_SHORT, [proto['STOP'][1]]])
- self.put(self.out_proto, ['STOP', None, None])
- self.put(self.out_ann, [ANN_SHIFTED, [protocol['STOP'][0]]])
- self.put(self.out_ann, [ANN_SHIFTED_SHORT, [protocol['STOP'][1]]])
-
- self.state = FIND_START
+ self.state = 'FIND START'
self.is_repeat_start = 0
self.wr = -1
super(Decoder, self).put(self.startsample, self.samplenum, output_id, data)
def decode(self, ss, es, data):
- for samplenum, (scl, sda) in data:
- self.samplenum = samplenum
+ for (self.samplenum, (scl, sda)) in data:
# First sample: Save SCL/SDA value.
if self.oldscl == None:
# TODO: Wait until the bus is idle (SDA = SCL = 1) first?
# State machine.
- if self.state == FIND_START:
+ if self.state == 'FIND START':
if self.is_start_condition(scl, sda):
self.found_start(scl, sda)
- elif self.state == FIND_ADDRESS:
+ elif self.state == 'FIND ADDRESS':
if self.is_data_bit(scl, sda):
self.found_address_or_data(scl, sda)
- elif self.state == FIND_DATA:
+ elif self.state == 'FIND DATA':
if self.is_data_bit(scl, sda):
self.found_address_or_data(scl, sda)
elif self.is_start_condition(scl, sda):
self.found_start(scl, sda)
elif self.is_stop_condition(scl, sda):
self.found_stop(scl, sda)
+ elif self.state == 'FIND ACK':
+ if self.is_data_bit(scl, sda):
+ self.get_ack(scl, sda)
else:
- # Shouldn't happen.
- raise Exception("unknown state %d" % self.STATE)
+ raise Exception('Invalid state %d' % self.STATE)
# Save current SDA/SCL values for the next round.
self.oldscl = scl