- fx2lafw: Logic analyzers based on the Cypress FX2(LP) chip need the
firmware files from the 'sigrok-firmware-fx2lafw' repository/project.
- The firmware is written from scratch and licensed under the GPLv2+.
+ The firmware is written from scratch and licensed under the GNU GPLv2+.
- hantek-dso: The Hantek DSO-2090 (and other supported models of the same
series of Hantek PC oscilloscopes) need firmware files.
These can be extracted from the vendor's Linux application using a tool
from our 'sigrok-util' repository/project.
+ - sysclk-lwla: The Sysclk LWLA1034 requires various bitstream files.
+ These files are available from our 'sigrok-firmware' repository/project
+ under a license which allows us to redistribute them.
+
The following drivers/devices do not need any firmware upload:
- agilent-dmm
- - alsa
- appa-55ii
+ - atten-pps3xxx
- brymen-bm86x
- brymen-dmm
- cem-dt-885x
- center-3xx (including all subdrivers)
- - chronovu-la8
+ - chronovu-la
- colead-slm
+ - conrad-digi-35-cpu
- demo
- fluke-dmm
- - gmc-mh-1x-2x
+ - gmc-mh-1x-2x (including all subdrivers)
- hameg-hmo
- ikalogic-scanalogic2
- ikalogic-scanaplus
- agilent-dmm
- appa-55ii
+ - atten-pps3xxx
- brymen-dmm
- cem-dt-885x
- center-3xx (including all subdrivers)
- colead-slm
+ - conrad-digi-35-cpu
- fluke-dmm
- - gmc-mh-1x-2x
+ - gmc-mh-1x-2x (including all subdrivers)
- hameg-hmo
- link-mso19
- mic-985xx (including all subdrivers)
The following drivers/devices do not require a serial port specification:
- - alsa
- asix-sigma
- brymen-bm86x
- - chronovu-la8
+ - chronovu-la
- demo
- fx2lafw
- hantek-dso
- lascar-el-usb
- rigol-ds (USBTMC or TCP)
- saleae-logic16
+ - sysclk-lwla
- uni-t-dmm (including all subdrivers)
- uni-t-ut32x
- victor-dmm
Every serial device's driver has default serial port parameters like baud
rate, number of data bits, stop bits and handshake status. If a device requires
different parameters, pass them as option "serialcomm" with the driver name.
-See libsigrok docs for function serial_set_paramstr() for complete specs.
+See libsigrok docs for the function serial_set_paramstr() for complete specs.
Example:
- Voltcraft VC-830: Press the "REL/PC" button for roughly 2 seconds.
-ALSA driver
------------
-
-The 'alsa' driver can be used to sample analog data using a PC's soundcard.
-I.e. the sound card can act as a simple oscilloscope (with some limitations)
-using commercial or DIY "sound card scope probe" cables.
-
-Since ALSA is a Linux-specific sound system, this driver will inherently
-only compile and work on Linux.
-
-We might write additional drivers to make a similar functionality available
-on other OSes at some point.
-
-
-Link Instruments MSO-19
------------------------
-
-The driver for the Link Instruments MSO-19 mixed-signal oscilloscope (MSO)
-is currently using libudev (which is a library for the Linux-specific udev
-system). Thus, this driver can currently only compile and work on Linux.
-
-We plan to fix this though, so that it'll work on all other OSes, too.
-
-
-ChronoVu LA8 USB VID/PIDs
--------------------------
+ChronoVu LA8/LA16 USB VID/PIDs
+------------------------------
-The ChronoVu LA8 logic analyzer is available in two revisions. Previously,
-the LA8 shipped with a USB VID/PID of 0403:6001, which is the standard ID
+The ChronoVu LA8/LA16 logic analyzer is available in two revisions. Previously,
+the device shipped with a USB VID/PID of 0403:6001, which is the standard ID
for FTDI FT232 USB chips.
-Since this made it hard to distinguish the LA8 from any other device
+Since this made it hard to distinguish the LA8/LA16 from any other device
with this FTDI chip connected to the PC, the vendor later shipped the
-LA8 with a USB VID/PID of 0403:8867.
+device with a USB VID/PID of 0403:8867.
-The 'chronovu-la8' driver in libsigrok supports both VID/PID pairs and
-automatically finds devices with either VID/PID pair. However, currently
-the driver will assume any device with VID/PID 0403:6001 is a ChronoVu LA8.
+The 'chronovu-la' driver in libsigrok supports both VID/PID pairs and
+automatically finds devices with either VID/PID pair.
OLS
---
-The Dangerous Prototypes Openbench Logic Sniffer (OLS) logic analyzer is
-supported by the 'ols' driver in libsigrok. This driver assumes a somewhat
-recent firmware has been flashed onto the OLS (it doesn't need a firmware
-upload every time it's attached via USB, since the firmware is stored in the
-device permanently).
+The Dangerous Prototypes Openbench Logic Sniffer (OLS) logic analyzer
+driver in libsigrok assumes a somewhat recent firmware has been flashed onto
+the OLS (it doesn't need a firmware upload every time it's attached via USB,
+since the firmware is stored in the device permanently).
The most recent firmware version that is tested is 3.07.
$ sigrok-cli --driver ols:conn=/dev/ttyACM0 ...
-
-Rigol DS oscilloscopes
-----------------------
-
-The 'rigol-ds' driver (for the Rigol DS series DSOs) currently uses the Linux
-usbtmc kernel driver. This means it can currently only be built and used on
-Linux (i.e., it's non-portable).
-
-The use of a kernel module also means it is dependent on the kernel version
-used, as well as on whether this specific module is available in the kernel.
-Additionally, the usbtmc kernel module has been known to have various bugs
-in some versions. These are some (but not all) drawbacks of using a kernel
-module as opposed to a libusb-based driver that works in user-space.
-
-We plan to change the driver to use the 'librevisa' user-space shared
-library (which uses libusb) soon, which will fix all these issues and make
-the driver portable at the same time.
projects / libsigrok.git / blobdiff