+/* For now, only the LWLA1034 is supported.
+ */
+#define VENDOR_NAME "SysClk"
+#define MODEL_NAME "LWLA1034"
+
+#define USB_VID_PID "2961.6689"
+#define USB_INTERFACE 0
+#define USB_TIMEOUT 3000 /* ms */
+
+#define NUM_PROBES 34
+#define TRIGGER_TYPES "01fr"
+
+/** Unit and packet size for the sigrok logic datafeed.
+ */
+#define UNIT_SIZE ((NUM_PROBES + 7) / 8)
+#define PACKET_SIZE (10000 * UNIT_SIZE) /* bytes */
+
+/** Size of the acquisition buffer in device memory units.
+ */
+#define MEMORY_DEPTH (256 * 1024) /* 256k x 36 bit */
+
+/** Number of device memory units (36 bit) to read at a time. Slices of 8
+ * consecutive 36-bit words are mapped to 9 32-bit words each, so the chunk
+ * length should be a multiple of 8 to ensure alignment to slice boundaries.
+ *
+ * Experimentation has shown that reading chunks larger than about 1024 bytes
+ * is unreliable. The threshold seems to relate to the buffer size on the FX2
+ * USB chip: The configured endpoint buffer size is 512, and with double or
+ * triple buffering enabled a multiple of 512 bytes can be kept in fly.
+ *
+ * The vendor software limits reads to 120 words (15 slices, 540 bytes) at
+ * a time. So far, it appears safe to increase this to 224 words (28 slices,
+ * 1008 bytes), thus making the most of two 512 byte buffers.
+ */
+#define READ_CHUNK_LEN (28 * 8)
+
+/** Calculate the required buffer size in 16-bit units for reading a given
+ * number of device memory words. Rounded to a multiple of 8 device words.
+ */
+#define LWLA1034_MEMBUF_LEN(count) (((count) + 7) / 8 * 18)
+
+/** Maximum number of 16-bit words sent at a time during acquisition.
+ * Used for allocating the libusb transfer buffer.
+ */
+#define MAX_ACQ_SEND_WORDS 8 /* 5 for memory read request plus stuffing */
+
+/** Maximum number of 16-bit words received at a time during acquisition.
+ * Round to the next multiple of the endpoint buffer size to avoid nasty
+ * transfer overflow conditions on hiccups.
+ */
+#define MAX_ACQ_RECV_WORDS ((READ_CHUNK_LEN / 4 * 9 + 255) / 256 * 256)
+
+/** Maximum length of a register write sequence.
+ */
+#define MAX_REG_WRITE_SEQ_LEN 5
+
+/** Default configured samplerate.
+ */
+#define DEFAULT_SAMPLERATE SR_MHZ(125)
+
+/** LWLA clock sources.
+ */
+enum clock_source {
+ CLOCK_SOURCE_NONE,
+ CLOCK_SOURCE_INT,
+ CLOCK_SOURCE_EXT_RISE,
+ CLOCK_SOURCE_EXT_FALL,
+};
+
+/** LWLA device states.
+ */
+enum device_state {
+ STATE_IDLE = 0,
+
+ STATE_START_CAPTURE,
+
+ STATE_STATUS_WAIT,
+ STATE_STATUS_REQUEST,
+ STATE_STATUS_RESPONSE,
+
+ STATE_STOP_CAPTURE,
+
+ STATE_LENGTH_REQUEST,
+ STATE_LENGTH_RESPONSE,
+
+ STATE_READ_PREPARE,
+ STATE_READ_REQUEST,
+ STATE_READ_RESPONSE,
+ STATE_READ_END,
+};
+
+/** LWLA run-length encoding states.
+ */
+enum rle_state {
+ RLE_STATE_DATA,
+ RLE_STATE_LEN
+};
+
+/** LWLA sample acquisition and decompression state.
+ */
+struct acquisition_state {
+ uint64_t sample;
+ uint64_t run_len;
+
+ /** Number of samples acquired so far. */
+ uint64_t captured_samples;
+ /** Number of samples sent to the session bus. */
+ uint64_t transferred_samples;
+
+ /** Capture memory fill level. */
+ size_t mem_addr_fill;