Add a DALI protocol decoder.

[libsigrokdecode.git] / decoders / dali / lists.py

diff --git a/decoders/dali/lists.py b/decoders/dali/lists.py
new file mode 100644 (file)
index 0000000..24e6bc4
--- /dev/null
+++ b/decoders/dali/lists.py
@@ -0,0 +1,98 @@
+##
+## This file is part of the libsigrokdecode project.
+##
+## Copyright (C) 2015 Jeremy Swanson <jeremy@rakocontrols.com>
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; either version 2 of the License, or
+## (at your option) any later version.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program.  If not, see <http://www.gnu.org/licenses/>.
+##
+
+# DALI Extended commands
+extendedCommands = {
+    0xA1: ['Terminate special processes', 'Terminate'],
+    0xA3: ['DTR = DATA', 'DTR'],
+    0xA5: ['INITIALISE', 'INIT'],
+    0xA7: ['RANDOMISE', 'RAND'],
+    0xA9: ['COMPARE', 'COMP'],
+    0xAB: ['WITHDRAW', 'WDRAW'],
+    0xB1: ['SET SEARCH H', 'SAH'],
+    0xB3: ['SET SEARCH M', 'SAM'],
+    0xB5: ['SET SEARCH L', 'SAL'],
+    0xB7: ['Program Short Address', 'ProgSA'],
+    0xB9: ['Verify Short Address', 'VfySA'],
+    0xBB: ['Query Short Address', 'QryShort'],
+    0xBD: ['Physical Selection', 'PysSel'],
+    0xC1: ['Enable Device Type X', 'EnTyp'],
+    0xC3: ['DTR1 = DATA', 'DTR1'],
+    0xC5: ['DTR2 = DATA', 'DTR2'],
+    0xC7: ['Write Memory Location', 'WRI'],
+}
+
+# List of commands
+DALICommands = {
+    0x00: ['Immediate Off', 'IOFF'],
+    0x01: ['Up 200ms', 'Up'],
+    0x02: ['Down 200ms', 'Down'],
+    0x03: ['Step Up', 'Step+'],
+    0x04: ['Step Down', 'Step-'],
+    0x05: ['Recall Maximum Level', 'Recall Max'],
+    0x06: ['Recall Minimum Level', 'Recall Min'],
+    0x07: ['Step down and off', 'Down Off'],
+    0x08: ['Step ON and UP', 'On Up'],
+    0x20: ['Reset', 'Rst'],
+    0x21: ['Store Dim Level in DTR', 'Level -> DTR'],
+    0x2A: ['Store DTR as Max Level', 'DTR->Max'],
+    0x2B: ['Store DTR as Min Level', 'DTR->Min'],
+    0x2C: ['Store DTR as Fail Level', 'DTR->Fail'],
+    0x2D: ['Store DTR as Power On Level', 'DTR->Poweron'],
+    0x2E: ['Store DTR as Fade Time', 'DTR->Fade'],
+    0x2F: ['Store DTR as Fade Rate', 'DTR->Rate'],
+    0x80: ['Store DTR as Short Address', 'DTR->Add'],
+    0x81: ['Enable Memory Write', 'WEn'],
+    0x90: ['Query Status', 'Status'],
+    0x91: ['Query Ballast', 'Ballast'],
+    0x92: ['Query Lamp Failure', 'LmpFail'],
+    0x93: ['Query Power On', 'Power On'],
+    0x94: ['Query Limit Error', 'Limit Err'],
+    0x95: ['Query Reset', 'Reset State'],
+    0x96: ['Query Missing Short Address', 'NoSrt'],
+    0x97: ['Query Version', 'Ver'],
+    0x98: ['Query DTR', 'GetDTR'],
+    0x99: ['Query Device Type', 'Type'],
+    0x9A: ['Query Physical Minimum', 'PhysMin'],
+    0x9B: ['Query Power Fail', 'PowerFailed'],
+    0x9C: ['Query DTR1', 'GetDTR1'],
+    0x9D: ['Query DTR2', 'GetDTR2'],
+    0xA0: ['Query Level', 'GetLevel'],
+    0xA1: ['Query Max Level', 'GetMax'],
+    0xA2: ['Query Min Level', 'GetMin'],
+    0xA3: ['Query Power On', 'GetPwrOn'],
+    0xA4: ['Query Fail Level', 'GetFail'],
+    0xA5: ['Query Fade Rate', 'GetRate'],
+    0xA6: ['Query Power Fail', 'PwrFail'],
+    0xC0: ['Query Groups 0-7', 'GetGrpsL'],
+    0xC1: ['Query Groups 7-15', 'GetGrpsH'],
+    0xC2: ['Query BRNH', 'BRNH'],
+    0xC3: ['Query BRNM', 'BRNM'],
+    0xC4: ['Query BRNL', 'BRNL'],
+    0xC5: ['Query Memory', 'GetMem'],
+}
+
+# DALI device type 8
+DALIDeviceType8 = {
+    0xE0: ['Set Temp X-Y Coordinate', 'Set X-Y'],
+    0xE2: ['Activate Colour Set point', 'Activate SetPoint'],
+    0xE7: ['Set Colour Temperature Tc', 'DTRs->ColTemp'],
+    0xF9: ['Query Features', 'QryFeats'],
+    0xFA: ['Query Current Setpoint Colour', 'GetSetPoint'],
+}