Difference between revisions of "PCE PCE-322A"
| Line 145: | Line 145: | ||
==== Status Response ==== | ==== Status Response ==== | ||
This is the response to the Memory Status (0xad 0xda) command. | |||
{| border="0" class="alternategrey sigroktable" | {| border="0" class="alternategrey sigroktable" | ||
| Line 163: | Line 165: | ||
| 0x01 | | 0x01 | ||
| 0xd2 | | 0xd2 | ||
| colspan=" | | 0x''YY'' 0x''XX''colspan="2" | Used memory blocks | ||
| 0x10 | | 0x''ZZ'' | Used bytes in the last used block | ||
| 0x10 or 0x20 | |||
|} | |} | ||
Revision as of 22:40, 30 November 2016
 | |
| Status | supported |
|---|---|
| Source code | pce-322a |
| Connectivity | USB/serial |
| Frequency range | 31.5Hz - 8kHz |
| Measurement range (A) | 30dB - 130dB |
| Resolution | 0.1dB |
| Accuracy (94dB@1kHz) | 1.4dB |
| Frequency weighting | A, C |
| Time weighting | F, S |
| Standards | IEC 61672-1 Class 2 |
| Website | pce-instruments.com |
The PCE PCE-322A is an IEC 61672-1 class 2 compliant sound level meter with USB connectivity.
Hardware
TODO
Photos
Device, front
Device, back
Device, side
Protocol
The device communicates at 115200 baud, no parity, 8 data bits, and 1 stop bit (115200/8n1).
Commands
None of the following commands are needed to receive live measurements from the device; see the next section.
The commands are always 2 byte and take no parameters, except for the one requesting memory blocks.
The following commands are supported:
| Command | Description |
|---|---|
| 0xac 0xff | Connect |
| 0xca 0xff | Disconnect |
| 0xaa 0xf1 | Toggle dBA/dBC |
| 0xaa 0xf2 | Toggle Scale (Auto, 30-80, 50-100, 80-130) |
| 0xaa 0xf3 | Toggle Min/Max/Current |
| 0xaa 0xf4 | Toggle Fast/Slow |
| 0xaa 0xf5 | Toggle Hold |
| 0xaa 0xf6 | Toggle Backlight |
| 0xaa 0xf7 | Toggle Time/Date |
| 0xaa 0xf8 | Power Off |
| 0x7e 0x00 ... | Setup Logging (see below) |
| 0xad 0xda | Memory Status |
| 0xd3 0xda 0xXX 0xYY | Transfer YYXX-th block of data (block length: 256) |
| 0xaa 0xc1 | Clear Memory |
Measurements and settings
Current settings and measurements are continually streamed over the serial bus, without any prompting from the PC. Data is encapsulated in packets of 13 bytes. The packets are structured as follows:
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 |
| 0x7f | Measurement | Flags/Mode | ? | Date | 0x00 | |||||||
Memory
Setup Request
A recording can be setup remotely (which will start instantly or after pressing a button).
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 |
| 0x7e | ? | Interval | Date | Flags | |||||
Status Response
This is the response to the Memory Status (0xad 0xda) command.
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
| 0xd1 | 0x05 | 0x00 | 0x01 | 0xd2 | Used memory blocks | Used bytes in the last used block | 0x10 or 0x20 |
Header
Each recording starts with a header:
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 |
| 0x7f | 0xf7 | 0x01 | 0x00 | 0x0a | Date | |||||