Difference between revisions of "Hameg HO730"
Jump to navigation
Jump to search
(start HO730 Hameg interface page) |
Uwe Hermann (talk | contribs) m |
||
| Line 25: | Line 25: | ||
idProduct 0xed73 '''HAMEG HO730 Serial Port''' | idProduct 0xed73 '''HAMEG HO730 Serial Port''' | ||
bcdDevice 4.00 | bcdDevice 4.00 | ||
iManufacturer 1 HAMEG Instruments | iManufacturer 1 '''HAMEG Instruments''' | ||
iProduct 2 Hameg HO730 | iProduct 2 '''Hameg HO730''' | ||
iSerial 3 014691501 | iSerial 3 014691501 | ||
bNumConfigurations 1 | bNumConfigurations 1 | ||
| Line 49: | Line 49: | ||
bInterfaceSubClass 255 Vendor Specific Subclass | bInterfaceSubClass 255 Vendor Specific Subclass | ||
bInterfaceProtocol 255 Vendor Specific Protocol | bInterfaceProtocol 255 Vendor Specific Protocol | ||
iInterface 2 Hameg HO730 | iInterface 2 '''Hameg HO730''' | ||
Endpoint Descriptor: | Endpoint Descriptor: | ||
bLength 7 | bLength 7 | ||
| Line 76: | Line 76: | ||
Identified chips on the PCB: | Identified chips on the PCB: | ||
* eZ80F91NA050SG (eZ80 MCU) | * eZ80F91NA050SG (eZ80 MCU) | ||
* | * Flash memory (near eZ80, for MCU firmware, covered by the version sticker) | ||
* | * Voltage regulator | ||
* KSZ8721BL (Micrel PHY) | * KSZ8721BL (Micrel PHY) | ||
* FTDI FT245BL (USB connectivity) | * FTDI FT245BL (USB connectivity) | ||
| Line 86: | Line 86: | ||
<gallery> | <gallery> | ||
File:ho730-face.png|<small> | File:ho730-face.png|<small>Connectors view</small> | ||
File:ho730-top.png|<small>PCB, top side</small> | File:ho730-top.png|<small>PCB, top side</small> | ||
File:ho730-bottom.png|<small>PCB, bottom side</small> | File:ho730-bottom.png|<small>PCB, bottom side</small> | ||
</gallery> | </gallery> | ||
Latest revision as of 16:25, 21 January 2017
The Hameg HO730 is a communication interface for Hameg test and measurement equipment. It provides both Ethernet 10/100 (RJ-45) and USB 2.0 (device, B) connections. The vendor states that the interface can be used with scope models in the HM, HMF, HMO, HMP, and HMS series.
Hardware
For Ethernet the module uses an eZ80 chip (Z80 CPU core, with some degree of hardware support for network communication) and a Micrel PHY.
For USB the module uses an FTDI FT245 chip.
$ lsusb -v -d 0403:ed73
Bus 003 Device 099: ID 0403:ed73 Future Technology Devices International, Ltd HAMEG HO730 Serial Port
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0403 Future Technology Devices International, Ltd
idProduct 0xed73 HAMEG HO730 Serial Port
bcdDevice 4.00
iManufacturer 1 HAMEG Instruments
iProduct 2 Hameg HO730
iSerial 3 014691501
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 32
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 2 Hameg HO730
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0001
Self Powered
Identified chips on the PCB:
- eZ80F91NA050SG (eZ80 MCU)
- Flash memory (near eZ80, for MCU firmware, covered by the version sticker)
- Voltage regulator
- KSZ8721BL (Micrel PHY)
- FTDI FT245BL (USB connectivity)
- Microwire(?) flash memory (near FTDI)
- 2x TI LC02A (7402 quad NOR gates? chip select logic? backplane glue?)
Photos
Connectors view
PCB, top side
PCB, bottom side
