Difference between revisions of "Protocol decoder:Rfm12"
Jump to navigation
Jump to search
m |
Uwe Hermann (talk | contribs) m |
||
| Line 1: | Line 1: | ||
{{Infobox protocol decoder | {{Infobox protocol decoder | ||
| id = rfm12 | | id = rfm12 | ||
| name = RFM12 | | name = RFM12 control protocol | ||
| description = | | description = HopeRF RFM12 wireless transceiver control protocol | ||
| status = supported | | status = supported | ||
| license = GPLv2+ | | license = GPLv2+ | ||
| Line 13: | Line 13: | ||
}} | }} | ||
The '''rfm12''' decoder supports the control protocol for the | The '''rfm12''' decoder supports the control protocol for the [http://www.hoperf.com/rf/fsk_module/RFM12B.htm HopeRF RFM12] transceiver chip. | ||
RFM12B is a single chip, low power, multi-channel FSK transceiver designed for use in applications requiring FCC or ETSI conformance for unlicensed use in the 433MHz, 868MHz and 915MHz bands. | |||
== Hardware == | == Hardware == | ||
These modules comes in three different form factors, DIP package (shown on the photo) and two SMD packages: S1 with normal crystal and S2 with low-profile crystal. | These modules comes in three different form factors, DIP package (shown on the photo) and two SMD packages: S1 with normal crystal and S2 with low-profile crystal. | ||
Pins: | Pins: | ||
{| border="0" style="font-size: smaller" class="alternategrey sigroktable" | {| border="0" style="font-size: smaller" class="alternategrey sigroktable sortable" | ||
|- | |- | ||
!Name | !Name | ||
| Line 27: | Line 30: | ||
|- | |- | ||
| nINT/VDI | | nINT/VDI | ||
| Interrupt input (active low)/ | | Interrupt input (active low) / valid data indicator | ||
|- | |- | ||
| Line 55: | Line 58: | ||
|- | |- | ||
| FSK/DATA/nFFS | | FSK/DATA/nFFS | ||
| Transmit FSK data input/ | | Transmit FSK data input / received data output (FIFO not used) / FIFO select | ||
|- | |- | ||
| DCLK/CFIL/FFIT | | DCLK/CFIL/FFIT | ||
| | | Clock output (no FIFO) / external filter capacitor (analog mode) / FIFO interrupts (active high) | ||
interrupts(active high) | |||
|- | |- | ||
| Line 76: | Line 78: | ||
== Protocol == | == Protocol == | ||
SPI communication happens in a fixed length 16-bit chunks. During each exchange the microcontroller first sends the command and then receives the response. | In minimal configuration the chip uses the standard SPI protocol on pins SDI, SDO, SCK and nSEL. You can optionally connect nIRQ which will be pulled low by the transceiver to trigger interrupt requests. There is also an option to transmit and receive the data without the SPI protocol overhead using the dedicated DATA and DCLK pins. | ||
SPI communication happens in a fixed length of 16-bit chunks. During each exchange the microcontroller first sends the command and then receives the response. | |||
== Decoder == | == Decoder == | ||
The | The '''rfm12''' decoder stacks on top of the [[Protocol decoder:spi|SPI decoder]] and decodes the SPI exchanges. It shows what commands were sent to the chip and decodes the responses. It also interprets the commands and shows what happened to the chip. | ||
Some decoded commands in [[PulseView]]: | Some decoded commands in [[PulseView]]: | ||
| Line 92: | Line 95: | ||
== Resources == | == Resources == | ||
* [http://www.hoperf.com/rf/fsk_module/RFM12B.htm RFM12 page on HopeRF site] | * [http://www.hoperf.com/rf/fsk_module/RFM12B.htm RFM12 page on HopeRF site] | ||
* [http://www.hoperf.com/upload/rf/RFM12.pdf RFM12 datasheet] | * [http://www.hoperf.com/upload/rf/RFM12.pdf RFM12 datasheet] | ||
Revision as of 11:55, 19 September 2014
 | |
| Name | RFM12 control protocol |
|---|---|
| Description | HopeRF RFM12 wireless transceiver control protocol |
| Status | supported |
| License | GPLv2+ |
| Source code | decoders/rfm12 |
| Input | spi |
| Output | rfm12 |
| Probes | — |
| Optional probes | — |
The rfm12 decoder supports the control protocol for the HopeRF RFM12 transceiver chip.
RFM12B is a single chip, low power, multi-channel FSK transceiver designed for use in applications requiring FCC or ETSI conformance for unlicensed use in the 433MHz, 868MHz and 915MHz bands.
Hardware
These modules comes in three different form factors, DIP package (shown on the photo) and two SMD packages: S1 with normal crystal and S2 with low-profile crystal.
Pins:
| Name | Function |
|---|---|
| nINT/VDI | Interrupt input (active low) / valid data indicator |
| VDD | Positive power supply |
| SDI | SPI data input |
| SCK | SPI clock input |
| nSEL | Chip select (active low) |
| SDO | SPI data output |
| nIRQ | Interrupt request output (active low) |
| FSK/DATA/nFFS | Transmit FSK data input / received data output (FIFO not used) / FIFO select |
| DCLK/CFIL/FFIT | Clock output (no FIFO) / external filter capacitor (analog mode) / FIFO interrupts (active high) |
| CLK | Clock output for external microcontroller |
| nRES | Reset output (active low) |
| GND | Power ground |
Protocol
In minimal configuration the chip uses the standard SPI protocol on pins SDI, SDO, SCK and nSEL. You can optionally connect nIRQ which will be pulled low by the transceiver to trigger interrupt requests. There is also an option to transmit and receive the data without the SPI protocol overhead using the dedicated DATA and DCLK pins.
SPI communication happens in a fixed length of 16-bit chunks. During each exchange the microcontroller first sends the command and then receives the response.
Decoder
The rfm12 decoder stacks on top of the SPI decoder and decodes the SPI exchanges. It shows what commands were sent to the chip and decodes the responses. It also interprets the commands and shows what happened to the chip.
Some decoded commands in PulseView:
Status command.
Receiver control command.
