Difference between revisions of "HT USBee-AxPro"

From sigrok
Jump to navigation Jump to search
(HT_V6.0)
(→‎Photos: HT2013 V5.00 (no button PCB))
Line 80: Line 80:
File:24LC64.jpg |<small>24LC64</small>
File:24LC64.jpg |<small>24LC64</small>
File:24LC02B.jpg |<small>24LC02B</small>
File:24LC02B.jpg |<small>24LC02B</small>
</gallery>
'''HT2013 V5.00 (no blue button PCB)''':
<gallery>
File:Ht usbee axpro v5 package contents.jpg|<small>Package contents</small>
File:Ht usbee axpro v5 device top.jpg|<small>Device, top</small>
File:Ht usbee axpro v5 device bottom.jpg|<small>Device, bottom</small>
File:Ht usbee axpro v5 connector.jpg|<small>Connector</small>
File:Ht usbee axpro v5 usb.jpg|<small>USB</small>
File:Ht usbee axpro v5 analog connector top.jpg|<small>Analog connector, top</small>
File:Ht usbee axpro v5 analog connector bottom.jpg|<small>Analog connector, bottom</small>
File:Ht usbee axpro v5 button conn.jpg|<small>Button connector</small>
File:Ht usbee axpro v5 pcb top.jpg|<small>PCB, top</small>
File:Ht usbee axpro v5 pcb bottom.jpg|<small>PCB, bottom</small>
File:Ht usbee axpro v5 cypress fx2.jpg|<small>Cypress FX2</small>
File:Ht usbee axpro v5 st stm8s003f3.jpg|<small>ST STM8S003F3</small>
File:Ht usbee axpro v5 microchip 24lc64i.jpg|<small>Microchip 24LC64I</small>
File:Ht usbee axpro v5 microchip 24lc02bi.jpg|<small>Microchip 24LC02BI</small>
File:Ht usbee axpro v5 intersil icl7660.jpg|<small>Intersil ICL7660</small>
File:Ht usbee axpro v5 ti tlc5510i.jpg|<small>TI TLC5510I</small>
File:Ht usbee axpro v5 ams1117-3.3.jpg|<small>AMS1117-3.3</small>
</gallery>
</gallery>



Revision as of 17:21, 3 July 2016

HT USBee-AxPro
Ht-usbee-axpro.png
Status supported
Source code fx2lafw
Channels 8
Samplerate 24MHz
Samplerate (state)
Triggers none (SW-only)
Min/max voltage Digital: -1V — +6V
Analog: ±10V (±20V max)
Threshold voltage Fixed: VIH=1.6V, VIL=1.4V
Memory none
Compression none

The HT USBee-AxPro is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel.

It is able to switch between USBee AX-Pro, Salea Logic and Altera USB blaster mode via a button. When pressing the button the USB VID/PID changes.

It is a clone of the CWAV USBee AX-Pro.

In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.

Hardware

HT2013 V5.00:

FX2LP pin mappings

# Pin Destination Remark
CTL2 ADC_CLK ADC clock
PD0..7 ADC_D1..8 ADC data output


HT_V6.0:

  • ...

Pin mappings

The FX2 CTL2 and PD0..7 pins are mapped exactly like the HT2013 V5.00 version. The TLC5510I OE# pin is tied to GND.

Photos

HT2013 V5.00:

HT2013 V5.00 (no blue button PCB):

HT_V6.0:

Protocol

Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.

Resources