Difference between revisions of "WCH CH9325"
Uwe Hermann (talk | contribs) m |
|||
| (7 intermediate revisions by 2 users not shown) | |||
| Line 4: | Line 4: | ||
[http://www.wch.cn/ WCH], also known as Nanjing Qin Heng Electronics, makes a series of microcontrollers, PCI interface chips, and USB interface chips. | [http://www.wch.cn/ WCH], also known as Nanjing Qin Heng Electronics, makes a series of microcontrollers, PCI interface chips, and USB interface chips. | ||
The CH9325 is a USB interface chip, which converts data received via UART to USB and vice versa. The chip presents a HID (Human Interface Device) USB profile, in an effort to not require USB driver installation: this is typically handled by the OS kernel. | The CH9325 is a USB interface chip, which converts data received via UART to USB/HID and vice versa. The chip presents a HID (Human Interface Device) USB profile, in an effort to not require USB driver installation: this is typically handled by the OS kernel. Examples of the profile are included in the [[Device_cables/Info#UNI-T_UT-D04|lsusb of the UNI-T UT-D04 DMM cable]] or the [[UNI-T UT325/Info|lsusb of the UNI-T UT325 temperature logger]]. | ||
The chip runs off of a 12MHz oscillator. | The chip runs off of a 12MHz oscillator. | ||
| Line 10: | Line 10: | ||
== Pin layout == | == Pin layout == | ||
{{chip_16pin|1=RESET|2=UART TX|3=UART RX|6=USB D+|7=USB D-|8=GND|9=OSC-|10=OSC+|15= | {{chip_16pin|1=RESET|2=UART TX|3=UART RX|4=TX ACT|5=VCC select|6=USB D+|7=USB D-|8=GND|9=OSC-|10=OSC+|15=VCC +5V}} | ||
Pin 4 goes high while transmitting data on UART TX (i.e. USB -> device). This is possibly intended for an activity LED. | |||
Assuming pin 5 (VCC select) has the same function as other WCH devices (such as CH341), tying it to GND via a decoupling capacitor selects +5V external power operation. Tying the pin to 3.3V selects 3.3V external power. | |||
== Protocol == | == Protocol == | ||
| Line 16: | Line 20: | ||
==== Chip configuration ==== | ==== Chip configuration ==== | ||
USB packets sent to endpoint 0 are intercepted by the chip, and serve to configure it. A | USB packets sent to endpoint 0 are intercepted by the chip, and serve to configure it. A configuration packet consists of (at least) 2 bytes: | ||
{| border="0" style="font-size: smaller; width: 90%;" class="alternategrey sigroktable" | {| border="0" style="font-size: smaller; width: 90%;" class="alternategrey sigroktable" | ||
| Line 26: | Line 30: | ||
| UART baudrate, in little-endian order. For example, <code>60 09</code> = 0x0960 = 2400. Supported baudrates are 2400, 4800, 9600 and 19200; setting any other rate defaults to 2400 instead. | | UART baudrate, in little-endian order. For example, <code>60 09</code> = 0x0960 = 2400. Supported baudrates are 2400, 4800, 9600 and 19200; setting any other rate defaults to 2400 instead. | ||
|- | |- | ||
| 3 | | 3, 4 | ||
| uncertain purpose, probably parity and stop bits specs, often omitted, or 0x00 is sent | |||
| | |||
|- | |- | ||
| 5 | | 5 | ||
| | | number of data bits (encoded, values 0-3 translate to 5-8 data bits) | ||
|} | |} | ||
Applications can get away with just sending the first two bytes. | |||
Vendor software has been observed sending 3 more bytes (00 00 03), but these seem to be not strictly required. | |||
Even though the chip defaults to 2400 baud, that is not the default on startup: the baudrate setting command MUST still be sent. | |||
==== USB encapsulation ==== | ==== USB encapsulation ==== | ||
| Line 47: | Line 53: | ||
Extracting the UART stream on the other side of the USB bus simply entails the reverse process: for every received packet, extract the payload according to the length byte (nibble). | Extracting the UART stream on the other side of the USB bus simply entails the reverse process: for every received packet, extract the payload according to the length byte (nibble). | ||
Transmit data is communicated in similar ways: The first byte contains the number of payload bytes which follow (without ''0xf0'' added as is the case for receive data). Up to 7 payload bytes follow. The complete block consists of exactly 8 bytes, with ''0x00'' padded when necessary. | |||
Latest revision as of 17:01, 15 June 2019
WCH, also known as Nanjing Qin Heng Electronics, makes a series of microcontrollers, PCI interface chips, and USB interface chips.
The CH9325 is a USB interface chip, which converts data received via UART to USB/HID and vice versa. The chip presents a HID (Human Interface Device) USB profile, in an effort to not require USB driver installation: this is typically handled by the OS kernel. Examples of the profile are included in the lsusb of the UNI-T UT-D04 DMM cable or the lsusb of the UNI-T UT325 temperature logger.
The chip runs off of a 12MHz oscillator.
Pin layout
| RESET | 1- | O | -16 | |
| UART TX | 2- | -15 | VCC +5V | |
| UART RX | 3- | -14 | ||
| TX ACT | 4- | -13 | ||
| VCC select | 5- | -12 | ||
| USB D+ | 6- | -11 | ||
| USB D- | 7- | -10 | OSC+ | |
| GND | 8- | -9 | OSC- |
Pin 4 goes high while transmitting data on UART TX (i.e. USB -> device). This is possibly intended for an activity LED.
Assuming pin 5 (VCC select) has the same function as other WCH devices (such as CH341), tying it to GND via a decoupling capacitor selects +5V external power operation. Tying the pin to 3.3V selects 3.3V external power.
Protocol
Chip configuration
USB packets sent to endpoint 0 are intercepted by the chip, and serve to configure it. A configuration packet consists of (at least) 2 bytes:
| Byte | Description |
|---|---|
| 1-2 | UART baudrate, in little-endian order. For example, 60 09 = 0x0960 = 2400. Supported baudrates are 2400, 4800, 9600 and 19200; setting any other rate defaults to 2400 instead.
|
| 3, 4 | uncertain purpose, probably parity and stop bits specs, often omitted, or 0x00 is sent |
| 5 | number of data bits (encoded, values 0-3 translate to 5-8 data bits) |
Applications can get away with just sending the first two bytes. Vendor software has been observed sending 3 more bytes (00 00 03), but these seem to be not strictly required.
Even though the chip defaults to 2400 baud, that is not the default on startup: the baudrate setting command MUST still be sent.
USB encapsulation
The chip stores bytes received via the UART RX pin into a buffer. It transfers the contents of the buffer to a HID packet at regular intervals (maximum 12ms). The HID packets are always 8 bytes long, with the first byte containing the number of payload bytes. This is encoded as 0xf0 + length. The next 7 bytes contain the payload, padded with zeroes. Thus, even if no data is ever received on the UART, the chip always sends at least one packet every 12ms containing:
f0 00 00 00 00 00 00 00
Here's a packet with 2 bytes payload:
f2 35 41 00 00 00 00 00
Extracting the UART stream on the other side of the USB bus simply entails the reverse process: for every received packet, extract the payload according to the length byte (nibble).
Transmit data is communicated in similar ways: The first byte contains the number of payload bytes which follow (without 0xf0 added as is the case for receive data). Up to 7 payload bytes follow. The complete block consists of exactly 8 bytes, with 0x00 padded when necessary.