]> sigrok.org Git - fx2grok.git/shortlog
fx2grok.git
2017-07-09 Uwe Hermannlayout: Load and resave via Kicad 4.0.5, update from...
2017-07-09 Uwe HermannRegenerate netlist.
2017-07-09 Uwe Hermannschematics: Load and resave via Kicad 4.0.5, fixup...
2014-07-22 Uwe HermannDrop references to obsolete sigrok-commits mailing...
2013-04-26 Uwe HermannREADME: Add "Copyright and license" section.
2013-04-06 Uwe HermannPCB: Arrange and connect various parts/pins.
2013-04-04 Uwe HermannVarious updates.
2013-03-26 Uwe HermannReplace 5x2 SMD connector with two 5x1 pins/pads.
2013-03-25 Uwe HermannUpdate PCB layout (removed resistor-pack).
2013-03-25 Uwe HermannUpdate netlist.
2013-03-25 Uwe HermannSchematics: Drop resistor-pack for now.
2012-10-23 Uwe HermannSchematics: Fix wiki page URL.
2012-10-23 Uwe HermannREADME: Update description and git URL.
2012-10-23 Uwe HermannFirst unfinished attempt at routing the board.
2012-10-23 Uwe HermannSwitch 5mil tracks, 0.2mm vias (0.25mm restring).
2012-10-23 Uwe HermannUpdate PCB to new netlist.
2012-10-23 Uwe Hermannschematic: Various simplifications and fixes, regen...
2012-06-06 Uwe HermannStart arranging components (unfinished).
2012-06-05 Uwe HermannStuff everything into 12mm x 12mm PCB borders.
2012-06-05 Uwe Hermannschematics: Fix typo.
2012-06-05 Uwe HermannDraw 16mm x 12mm PCB borders (for now).
2012-06-04 Uwe HermannPCB: Tigthen DRC settings.
2012-06-04 Uwe HermannRe-read netlist in the PCB.
2012-06-04 Uwe HermannAdd CONN-5x2-SMD-127MM footprint.
2012-06-04 Uwe HermannUpdate netlist.
2012-06-04 Uwe Hermannschematics: Add 10pin connector for the probes.
2012-06-04 Uwe Hermannschematics: Replace 0603 resistorpack with 0402 one.
2012-06-04 Uwe HermannAdd RPACK-8-SMD-0402 footprint.
2012-06-04 Uwe HermannUpdate PCB due to netlist changes.
2012-06-04 Uwe HermannRegenerate netlist.
2012-06-04 Uwe Hermannschematics: Change all 0603 parts to 0402.
2012-06-04 Uwe HermannStart arranging parts.
2012-06-03 Uwe HermannPCB: Disperse parts a bit.
2012-06-03 Uwe HermannPCB: Read in netlist.
2012-06-03 Uwe HermannPCB: Set DRC values (min. widths etc).
2012-06-03 Uwe HermannRe-create netlist.
2012-06-03 Uwe HermannBugfix: Replace 2-pin CRYSTAL with 4-pin QUARTZCMS4.
2012-06-03 Uwe HermannMicro-USB B SMD footprint: Add missing SHIELD pin numbers.
2012-06-03 Uwe HermannRe-run 'Annotate schematic'.
2012-06-03 Uwe Hermannschematic: RESET# needs a 2K7 and 1uF (TRM, p. 83).
2012-06-03 Uwe HermannAdd QFN56 (0.5mm pin spacing) footprint.
2012-06-03 Uwe HermannAdd AMB11 footprint (crystal).
2012-06-03 Uwe HermannAdd RPACK-8-SMD-0603 footprint.
2012-06-03 Uwe HermannAdd empty PCB.
2012-06-03 Uwe HermannGenerate netlist.
2012-06-03 Uwe Hermannschematic: Annotate all components.
2012-06-03 Uwe HermannAdd missing footprint for the resistorpack.
2012-06-03 Uwe Hermannschematic: Various fixes, add metadata.
2012-06-03 Uwe Hermannschematic: Add PWR_FLAG (Kicad-internal stuff).
2012-06-03 Uwe HermannAdd new footprint library to project.
2012-06-03 Uwe HermannAdd a MICRO-USB-B-SMD footprint to a new library.
2012-06-03 Uwe HermannAdd some more footprints for symbols.
2012-06-03 Uwe HermannMark a few more pins as no-connect for now.
2012-06-03 Uwe HermannFix a few pin types.
2012-06-03 Uwe HermannBugfix: USB shield pins were not properly connected.
2012-06-03 Uwe HermannAdd footprints for all 0603 parts.
2012-06-03 Uwe HermannAdd resistorpack (8 x 100 Ohm) to PB0-PB7.
2012-06-03 Uwe HermannAdd two optional general-purpose LEDs (PD0/1).
2012-06-03 Uwe HermannAdd a power LED.
2012-06-03 Uwe HermannReplace TLV1117 with MIC5319.
2012-06-02 Uwe HermannChange Mini-USB B to Micro-USB B connector.
2012-06-02 Uwe HermannFX2: Use "IC", not "U" for the chip refdes.
2012-06-02 Uwe HermannRESET# is tied to VCC via a resistor.
2012-06-02 Uwe HermannVarious updates, move stuff around, add pin names.
2012-06-02 Uwe HermannUse 12pF load capacitors for the crystal.
2012-06-02 Uwe Hermann2.2uF/100nF for all AVCC pins (as per docs).
2012-06-02 Uwe HermannAdd 100nF bypass caps for all VCC pins.
2012-06-02 Uwe HermannFX2: The WAKEUP pin is tied to VCC via a 100K resistor.
2012-06-02 Uwe HermannFX2: The RESERVED pin needs to be tied to GND.
2012-06-02 Uwe HermannAdd I2C pullups (2.2kOhm).
2012-06-02 Uwe HermannAdd a README.
2012-06-01 Uwe Hermannlib: FX2 symbol: Nicer active-low pin marking.
2012-06-01 Uwe HermannAdd VCC/GND circuitry, mark PA0-7/PD0-7 as no-connect.
2012-06-01 Uwe HermannAdd initial XTAL circuitry.
2012-06-01 Uwe HermannAdd initial USB connector circuitry.
2012-06-01 Uwe HermannAdd initial TLV1117 circuitry.
2012-06-01 Uwe HermannFill background of FX2 component.
2012-06-01 Uwe HermannPlace FX2, TLV1117, and USB connector components.
2012-06-01 Uwe HermannAdd TLV1117-33 symbol to library.
2012-06-01 Uwe HermannAdd MINI-USB-B-SMD symbol to library.
2012-06-01 Uwe HermannAdd fx2grok-cube.lib library to project.
2012-06-01 Uwe HermannMove files to 0.1 subdir.
2012-06-01 Uwe HermannAdd initial Cypress CY7C68013A-56 symbol.
2012-06-01 Uwe HermannAdd empty schematics.
2012-06-01 Uwe HermannAdd empty Kicad project.