--- /dev/null
+/*
+ * This file is part of the libsigrok project.
+ *
+ * Copyright (C) 2019 Vitaliy Vorobyov
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef LIBSIGROK_HARDWARE_SYSCLK_SLA5032_PROTOCOL_H
+#define LIBSIGROK_HARDWARE_SYSCLK_SLA5032_PROTOCOL_H
+
+#include <stdint.h>
+#include <libusb.h>
+#include <glib.h>
+#include <libsigrok/libsigrok.h>
+#include <libsigrok-internal.h>
+
+#define LOG_PREFIX "sysclk-sla5032"
+
+/* Maximum configurable sample count limit. */
+#define MAX_LIMIT_SAMPLES (64 * 1024 * 1024)
+#define MIN_LIMIT_SAMPLES 512
+
+/* USB vendor and product IDs. */
+enum {
+ USB_VID_SYSCLK = 0x2961,
+ USB_PID_SLA5032 = 0x66B0,
+};
+
+/* USB device characteristics. */
+enum {
+ USB_CONFIG = 1,
+ USB_INTERFACE = 0,
+ USB_CMD_TIMEOUT_MS = 5000,
+ USB_REPLY_TIMEOUT_MS = 500000,
+ USB_DATA_TIMEOUT_MS = 2000,
+};
+
+/* USB device end points. */
+enum usb_endpoint {
+ EP_COMMAND = 4 | LIBUSB_ENDPOINT_OUT,
+ EP_REPLY = 8 | LIBUSB_ENDPOINT_IN,
+ EP_DATA = 6 | LIBUSB_ENDPOINT_IN,
+};
+
+
+/* Common indicator for no or unknown FPGA config. */
+enum {
+ FPGA_NOCONF = -1,
+ FPGA_CONF,
+};
+
+/** Acquisition protocol states. */
+enum protocol_state {
+ /* idle states */
+ STATE_IDLE = 0,
+ STATE_STATUS_WAIT,
+ /* device command states */
+ STATE_START_CAPTURE,
+ STATE_STOP_CAPTURE,
+ STATE_READ_PREPARE,
+ STATE_READ_FINISH,
+ /* command followed by response */
+ STATE_EXPECT_RESPONSE = 1 << 3,
+ STATE_STATUS_REQUEST = STATE_EXPECT_RESPONSE,
+ STATE_LENGTH_REQUEST,
+ STATE_READ_REQUEST,
+};
+
+/** SLA5032 protocol command ID codes. */
+enum command_id {
+ CMD_INIT_FW_UPLOAD = 1,
+ CMD_UPLOAD_FW_CHUNK = 2,
+ CMD_READ_REG = 3,
+ CMD_WRITE_REG = 4,
+ CMD_READ_MEM = 5,
+ CMD_READ_DATA = 7,
+};
+
+struct dev_context {
+ uint64_t samplerate; /* requested samplerate */
+ uint64_t limit_samples; /* requested capture length (samples) */
+ uint64_t capture_ratio;
+
+ uint64_t channel_mask; /* bit mask of enabled channels */
+ uint64_t trigger_mask; /* trigger enable mask */
+ uint64_t trigger_edge_mask; /* trigger type mask */
+ uint64_t trigger_values; /* trigger level/slope bits */
+
+ struct soft_trigger_logic *stl;
+ gboolean trigger_fired;
+
+ int active_fpga_config; /* FPGA configuration index */
+
+ enum protocol_state state; /* async protocol state */
+};
+
+SR_PRIV int sla5032_start_acquisition(const struct sr_dev_inst *sdi);
+SR_PRIV int sla5032_apply_fpga_config(const struct sr_dev_inst *sdi);
+
+#endif