Some devices supported by libsigrok need a firmware to be uploaded every time
the device is connected to the PC (usually via USB), before it can be used.
-The default location where libsigrok expects the firmware files is:
+The default locations where libsigrok expects the firmware files are:
+ $SIGROK_FIRMWARE_DIR (environment variable)
+ $HOME/.local/share/sigrok-firmware
$prefix/share/sigrok-firmware
+ /usr/local/share/sigrok-firmware
+ /usr/share/sigrok-firmware
($prefix is usually /usr/local or /usr, depending on your ./configure options)
firmware files from the 'sigrok-firmware-fx2lafw' repository/project.
The firmware is written from scratch and licensed under the GNU GPLv2+.
+ - hantek-6xxx: Certain oscilloscopes based on the Cypress FX2(LP) chip, such
+ as the Hantek 6022BE/6022BL, SainSmart DDS120, and Rocktech BM102, need the
+ firmware files from the 'sigrok-firmware-fx2lafw' repository/project.
+ The firmware is written from scratch and licensed under the GNU GPLv2+.
+
- hantek-dso: The Hantek DSO-2090 (and other supported models of the same
series of Hantek PC oscilloscopes) need firmware files.
These can be extracted from the vendor's Windows drivers using a tool
from our 'sigrok-util' repository/project.
+ - lecroy-logicstudio: The LeCroy LogicStudio requires FPGA bitstream files.
+ These can be extracted from the vendor's Windows software using a tool
+ from our 'sigrok-util' repository/project.
+ Additionally, it requires a Cypress FX2 firmware. This can be extracted
+ from the vendor's Windows software using another tool. Details:
+
+ http://sigrok.org/wiki/LeCroy_LogicStudio#Firmware
+
- saleae-logic16: The Saleae Logic16 needs a firmware file for the
Cypress FX2 chip in the device, as well as two FPGA bitstream files.
These can be extracted from the vendor's Linux application using a tool
from our 'sigrok-util' repository/project.
- - sysclk-lwla: The Sysclk LWLA1034 requires various bitstream files.
- These files are available from our 'sigrok-firmware' repository/project
- under a license which allows us to redistribute them.
+ - sysclk-lwla:
+
+ - The Sysclk LWLA1034 requires various bitstream files.
+ These files are available from our 'sigrok-firmware' repository/project
+ under a license which allows us to redistribute them.
+
+ - The Sysclk LWLA1016 requires various bitstream files.
+ These can be extracted from the vendor's Windows drivers using a tool
+ from our 'sigrok-util' repository/project.
The following drivers/devices do not need any firmware upload:
- agilent-dmm
- appa-55ii
+ - arachnid-labs-re-load-pro
- atten-pps3xxx
+ - baylibre-acme
+ - beaglelogic
- brymen-bm86x
- brymen-dmm
- cem-dt-885x
- conrad-digi-35-cpu
- demo
- fluke-dmm
+ - ftdi-la
- gmc-mh-1x-2x (including all subdrivers)
+ - gwinstek-gds-800
- hameg-hmo
+ - hp-3457a
+ - hung-chang-dso-2100
- ikalogic-scanalogic2
- ikalogic-scanaplus
- kecheng-kc-330b
+ - kern-scale
- lascar-el-usb
- link-mso19
+ - manson-hcs-3xxx
+ - maynuo-m97
- mic-985xx (including all subdrivers)
+ - motech-lps-30x
- norma-dmm
- openbench-logic-sniffer
+ - pce-322a
- pipistrello-ols
- rigol-ds
+ - scpi-pps
- serial-dmm (including all subdrivers)
+ - serial-lcr (including all subdrivers)
+ - siglent-sds
- teleinfo
+ - testo
- tondaj-sl-814
- uni-t-dmm (including all subdrivers)
- uni-t-ut32x
-----------------------
Many devices supported by libsigrok use serial port based cables (real RS232
-or USB-to-serial ones) to connect to a PC.
+or USB-to-serial ones, CDC class) to connect to a PC. These serial cables are
+supported by the libserialport library. Some vendors prefer to use HID chips
+instead of CDC chips in their serial cables. These cables can get supported
+by means of the hidapi library. Note that each chip type requires specific
+support in the libsigrok library. Bluetooth connected devices may be supported
+as well when they communicate by means of RFCOMM channels, or one of the
+implemented BLE notification/indication approaches, and one of the Bluetooth
+supporting platforms is used.
For all these devices, you need to specify the serial port they are connected
to (e.g. using the 'conn' option in sigrok-cli). It is not possible to scan
Example:
$ sigrok-cli --driver <somedriver>:conn=/dev/ttyUSB0 ...
-
-The following drivers/devices require a serial port specification:
+ $ sigrok-cli --driver <somedriver>:conn=hid/cp2110 ...
+ $ sigrok-cli --driver <somedriver>:conn=bt/rfcomm/01-23-45-67-89-ab ...
+
+Formal syntax for serial communication:
+
+ - COM ports (RS232, USB CDC):
+ conn=<com-port>
+ - USB HID cables:
+ conn=hid[/<chip>]
+ conn=hid[/<chip>]/usb=<bus>.<dev>[.<if>]
+ conn=hid[/<chip>]/raw=<path>
+ conn=hid[/<chip>]/sn=<serno>
+ chip can be: ch9325, cp2110
+ path may contain slashes
+ path and serno are "greedy" (span to the end of the spec)
+ - Bluetooth Classic and Bluetooth Low Energy (BLE):
+ conn=bt/<conn>/<addr>
+ conn can be: rfcomm, ble122, nrf51, cc254x
+ addr can be "dense" or separated, bt/cc254x/0123456789ab or
+ bt/rfcomm/11-22-33-44-55-66 or bt/ble122/88:6b:12:34:56:78
+ (note that colons may not be available when the conn= spec is taken
+ from a string that separates fields by colon, e.g. in the "--driver
+ <name>:conn=<spec>" example, that is why the dense form and the use
+ of dashes for separation are supported)
+
+The following drivers/devices require a serial port specification. Some of
+the drivers implement a default for the connection. Some of the drivers
+can auto-detect USB connected devices.
- agilent-dmm
- appa-55ii
- openbench-logic-sniffer
- rigol-ds (for RS232; not required for USBTMC or TCP)
- serial-dmm (including all subdrivers)
+ - serial-lcr (including all subdrivers)
- teleinfo
- tondaj-sl-814
+ - uni-t-dmm (all -ser subdrivers)
+ - uni-t-ut32x
The following drivers/devices do not require a serial port specification:
- rigol-ds (USBTMC or TCP)
- saleae-logic16
- sysclk-lwla
- - uni-t-dmm (including all subdrivers)
- - uni-t-ut32x
+ - uni-t-dmm (all non -ser subdrivers)
- victor-dmm
- yokogawa-dlm (USBTMC or TCP)
- zeroplus-logic-cube
+Beyond strict serial communication over COM ports (discussed above), the
+conn= property can also address specific USB devices, as well as specify TCP
+or VXI communication parameters. See these examples:
-Specifiying serial port parameters
-----------------------------------
+ $ sigrok-cli --driver <somedriver>:conn=<vid>.<pid> ...
+ $ sigrok-cli --driver <somedriver>:conn=tcp-raw/<ipaddr>/<port> ...
+ $ sigrok-cli --driver <somedriver>:conn=vxi/<ipaddr> ...
+ $ sigrok-cli --driver <somedriver>:conn=usbtmc/<bus>.<addr> ...
+
+The following drivers/devices accept network communication parameters:
+
+ - hameg-hmo
+ - rigol-ds
+ - scpi-dmm
+ - siglent-sds
+ - yokogawa-dlm
+
+
+Specifying serial port parameters
+---------------------------------
Every serial device's driver has default serial port parameters like baud
rate, number of data bits, stop bits and handshake status. If a device requires
(see below for details).
-Permissions for USB devices (udev rules file)
----------------------------------------------
+Permissions for USB devices (udev rules files)
+----------------------------------------------
When using USB-based devices supported by libsigrok, the user running the
libsigrok frontend (e.g. sigrok-cli) has to have (read/write) permissions
for the respective USB device.
-On Linux, this is accomplished using either 'chmod' (not recommended) or
-using the udev rules file shipped with libsigrok (recommended).
+On Linux, this is accomplished using udev rules. libsigrok ships a rules
+file containing all supported devices which can be detected reliably
+(generic USB-to-serial converters are omitted, as these are used for a wide
+range of devices, e.g. GPS receivers, which are not handled by libsigrok).
-The file is available in contrib/z60_libsigrok.rules. It contains entries
-for all libsigrok-supported (USB-based) devices and changes their group
-to 'plugdev' and the permissions to '664'.
+The file is available in contrib/60-libsigrok.rules. This file just contains
+the list of devices and flags these devices with ID_SIGROK="1". Access is
+granted by the 61-libsigrok-plugdev.rules or 61-libsigrok-uaccess.rules files,
+allowing access to members of the plugdev group or to currently logged in
+users, respectively.
When using a libsigrok package from your favorite Linux distribution, the
-packager will have already taken care of properly installing the udev file
-in the correct (distro-specific) place, and you don't have to do anything.
-The packager might also have adapted 'plugdev' and '664' as needed.
+files should already be installed in /usr/lib/udev/rules.d/, i.e.
+60-libsigrok.rules and one of the access granting rules files. Use of
+61-libsigrok-uaccess.rules is encouraged on systemd distributions.
+
+The access policy can be locally overridden by placing appropriate rules in
+/etc/udev/rules.d/, disabling or ammending the default policy. See the
+udev documentation, e.g. man 7 udev, for details.
If you're building from source, you need to copy the file to the place
-where your distro expects such files. This is beyond the scope of this README,
-but generally the location could be e.g. /etc/udev/rules.d, or maybe
-/lib/udev/rules.d, or something else. Afterwards you might have to restart
-udev, e.g. via '/etc/init.d/udev restart' or similar, and you'll have to
-re-attach your device via USB.
+where udev will read these rules. Local rules should go to /etc/udev/rules.d.
+Keep the file naming, otherwise interaction between the libsigrok rules and
+rules shipped by the system will be broken.
-Please consult the udev docs of your distro for details.
+Please consult the udev docs for details.
Cypress FX2 based devices
UNI-T multimeters (and rebranded devices, e.g. some Voltcraft models) can
ship with different PC connectivity cables:
+ - UT-D02 (RS232 cable)
- UT-D04 (USB/HID cable with Hoitek HE2325U chip, USB VID/PID 04fa:2490)
- UT-D04 (USB/HID cable with WCH CH9325 chip, USB VID/PID 1a86:e008)
- - UT-D02 (RS232 cable)
+ - UT-D07 (Bluetooth adapter, ISSC BL79 BLETR chip)
+ - UT-D09 (USB/HID cable with SiL CP2110 chip, USB VID/PID 10c4:ea80)
The above cables are all physically compatible (same IR connector shape)
with all/most currently known UNI-T multimeters. For example, you can
- BBC Goertz Metrawatt M2110: Briefly press the "Start/Reset" button on the
interface panel on top.
+ - Brymen BM257s: Press HOLD during power-on.
- Digitek DT4000ZC: Briefly press the "RS232" button.
+ - EEVBlog 121GW: Hold "1ms PEAK" until the "BT" indicator is shown.
+ - ES51919 based LCR meters (DER EE DE-5000, PeakTech 2170, UNI-T UT612):
+ Press the button with the "RS232" or "USB" or "PC link" label (usually
+ the "up" cursor button).
- Gossen Metrawatt Metrahit 1x/2x devices, driver gmc-mh-1x-2x-rs232:
- Power on the device with the "DATA" button pressed.
- Metrahit 2x devices must be configured for the respective interface type.
'SI232 online' (28-29S) or 'SI232 store' (22-26x). The interface must
be configured to the same baud rate as the host (default 9600).
Multimeter and interface must be configured to the same address.
+ - Metrix MX56C: Press the PRINT button to have the meter send acquisition
+ data via IR. Hold the PRINT button to adjust the meter's transmission
+ interval.
- Norma DM950: If the interface doesn't work (e.g. USB-RS232 converter), power
on the device with "FUNC" pressed (to power the interface from the DMM).
- PCE PCE-DM32: Briefly press the "RS232" button.
- V&A VA18B/VA40B: Keep the "Hz/DUTY" key pressed while powering on the DMM.
- Victor 70C/86C: Press the "REL/RS232" button for roughly 1 second.
- Voltcraft VC-830: Press the "REL/PC" button for roughly 2 seconds.
+ - Voltcraft VC-870: Press the "REL/PC" button for roughly 1 second.
ChronoVu LA8/LA16 USB VID/PIDs