/* Update sr_strerror()/sr_strerror_name() (error.c) upon changes! */
};
+/** Ternary return type for DMM/LCR/etc packet parser validity checks. */
+enum sr_valid_code {
+ SR_PACKET_INVALID = -1, /**< Certainly invalid. */
+ SR_PACKET_VALID = 0, /**< Certainly valid. */
+ SR_PACKET_NEED_RX = +1, /**< Need more RX data. */
+};
+
#define SR_MAX_CHANNELNAME_LEN 32
/* Handy little macros */
#define SR_HZ(n) (n)
-#define SR_KHZ(n) ((n) * (uint64_t)(1000ULL))
-#define SR_MHZ(n) ((n) * (uint64_t)(1000000ULL))
-#define SR_GHZ(n) ((n) * (uint64_t)(1000000000ULL))
+#define SR_KHZ(n) ((n) * UINT64_C(1000))
+#define SR_MHZ(n) ((n) * UINT64_C(1000000))
+#define SR_GHZ(n) ((n) * UINT64_C(1000000000))
-#define SR_HZ_TO_NS(n) ((uint64_t)(1000000000ULL) / (n))
+#define SR_HZ_TO_NS(n) (UINT64_C(1000000000) / (n))
/** libsigrok loglevels. */
enum sr_loglevel {
SR_T_DOUBLE_RANGE,
SR_T_INT32,
SR_T_MQ,
+ SR_T_UINT32,
/* Update sr_variant_type_get() (hwdriver.c) upon changes! */
};
SR_DF_TRIGGER,
/** Payload is struct sr_datafeed_logic. */
SR_DF_LOGIC,
- /** DEPRECATED! Use SR_DF_ANALOG instead. */
- SR_DF_ANALOG_OLD,
/** Beginning of frame. No payload. */
SR_DF_FRAME_BEGIN,
/** End of frame. No payload. */
SR_MQ_APPARENT_POWER,
/** Mass */
SR_MQ_MASS,
+ /** Harmonic ratio */
+ SR_MQ_HARMONIC_RATIO,
+ /** Energy. */
+ SR_MQ_ENERGY,
+ /** Electric charge. */
+ SR_MQ_ELECTRIC_CHARGE,
/* Update sr_key_info_mq[] (hwdriver.c) upon changes! */
};
SR_UNIT_SIEMENS,
/**
* An absolute measurement of power, in decibels, referenced to
- * 1 milliwatt (dBu).
+ * 1 milliwatt (dBm).
*/
SR_UNIT_DECIBEL_MW,
/** Voltage in decibel, referenced to 1 volt (dBV). */
SR_UNIT_VOLT_AMPERE,
/** Real power [W]. */
SR_UNIT_WATT,
- /** Consumption [Wh]. */
+ /** Energy (consumption) in watt hour [Wh]. */
SR_UNIT_WATT_HOUR,
/** Wind speed in meters per second. */
SR_UNIT_METER_SECOND,
SR_UNIT_TOLA,
/** Pieces (number of items). */
SR_UNIT_PIECE,
+ /** Energy in joule. */
+ SR_UNIT_JOULE,
+ /** Electric charge in coulomb. */
+ SR_UNIT_COULOMB,
+ /** Electric charge in ampere hour [Ah]. */
+ SR_UNIT_AMPERE_HOUR,
/*
* Update unit_strings[] (analog.c) and fancyprint() (output/analog.c)
SR_MQFLAG_REFERENCE = 0x80000,
/** Unstable value (hasn't settled yet). */
SR_MQFLAG_UNSTABLE = 0x100000,
+ /** Measurement is four wire (e.g. Kelvin connection). */
+ SR_MQFLAG_FOUR_WIRE = 0x200000,
/*
* Update mq_strings[] (analog.c) and fancyprint() (output/analog.c)
void *data;
};
-/** Analog datafeed payload for type SR_DF_ANALOG_OLD. */
-struct sr_datafeed_analog_old {
- /** The channels for which data is included in this packet. */
- GSList *channels;
- /** Number of samples in data */
- int num_samples;
- /** Measured quantity (voltage, current, temperature, and so on).
- * Use SR_MQ_VOLTAGE, ... */
- int mq;
- /** Unit in which the MQ is measured. Use SR_UNIT_VOLT, ... */
- int unit;
- /** Bitmap with extra information about the MQ. Use SR_MQFLAG_AC, ... */
- uint64_t mqflags;
- /** The analog value(s). The data is interleaved according to
- * the channels list. */
- float *data;
-};
-
/** Analog datafeed payload for type SR_DF_ANALOG. */
struct sr_datafeed_analog {
void *data;
gboolean is_signed;
gboolean is_float;
gboolean is_bigendian;
- uint8_t digits;
+ /**
+ * Number of significant digits after the decimal point, if positive.
+ * When negative, exponent with reversed polarity that is necessary to
+ * express the value with all digits without a decimal point.
+ * Refers to the value we actually read on the wire.
+ *
+ * Examples:
+ *
+ * | Disp. value | Exp. notation | Exp. not. normalized | digits |
+ * |-------------|---------------------|----------------------|--------|
+ * | 12.34 MOhm | 1.234 * 10^7 Ohm | 1234 * 10^4 Ohm | -4 |
+ * | 1.2345 MOhm | 1.2345 * 10^6 Ohm | 12345 * 10^2 Ohm | -2 |
+ * | 123.4 kOhm | 1.234 * 10^5 Ohm | 1234 * 10^2 Ohm | -2 |
+ * | 1234 Ohm | 1.234 * 10^3 Ohm | 1234 * 10^0 Ohm | 0 |
+ * | 12.34 Ohm | 1.234 * 10^1 Ohm | 1234 * 10^-2 Ohm | 2 |
+ * | 0.0123 Ohm | 1.23 * 10^-2 Ohm | 123 * 10^-4 Ohm | 4 |
+ * | 1.234 pF | 1.234 * 10^-12 F | 1234 * 10^-15 F | 15 |
+ */
+ int8_t digits;
gboolean is_digits_decimal;
struct sr_rational scale;
struct sr_rational offset;
};
struct sr_analog_spec {
- uint8_t spec_digits;
+ /**
+ * Number of significant digits after the decimal point, if positive.
+ * When negative, exponent with reversed polarity that is necessary to
+ * express the value with all digits without a decimal point.
+ * Refers to vendor specifications/datasheet or actual device display.
+ *
+ * Examples:
+ *
+ * | On the wire | Exp. notation | Exp. not. normalized | spec_digits |
+ * |-------------|---------------------|----------------------|-------------|
+ * | 12.34 MOhm | 1.234 * 10^7 Ohm | 1234 * 10^4 Ohm | -4 |
+ * | 1.2345 MOhm | 1.2345 * 10^6 Ohm | 12345 * 10^2 Ohm | -2 |
+ * | 123.4 kOhm | 1.234 * 10^5 Ohm | 1234 * 10^2 Ohm | -2 |
+ * | 1234 Ohm | 1.234 * 10^3 Ohm | 1234 * 10^0 Ohm | 0 |
+ * | 12.34 Ohm | 1.234 * 10^1 Ohm | 1234 * 10^-2 Ohm | 2 |
+ * | 0.0123 Ohm | 1.23 * 10^-2 Ohm | 123 * 10^-4 Ohm | 4 |
+ * | 1.234 pF | 1.234 * 10^-12 F | 1234 * 10^-15 F | 15 |
+ */
+ int8_t spec_digits;
};
/** Generic option struct used by various subsystems. */
struct sr_option {
/* Short name suitable for commandline usage, [a-z0-9-]. */
- char *id;
+ const char *id;
/* Short name suitable for GUI usage, can contain UTF-8. */
- char *name;
+ const char *name;
/* Description of the option, in a sentence. */
- char *desc;
+ const char *desc;
/* Default value for this option. */
GVariant *def;
/* List of possible values, if this is an option with few values. */
/** Data type like SR_T_STRING, etc if applicable. */
int datatype;
/** Short, lowercase ID string, e.g. "serialcomm", "voltage". */
- char *id;
+ const char *id;
/** Full capitalized name, e.g. "Serial communication". */
- char *name;
+ const char *name;
/** Verbose description (unused currently). */
- char *description;
+ const char *description;
};
-#define SR_CONF_GET (1 << 31)
-#define SR_CONF_SET (1 << 30)
-#define SR_CONF_LIST (1 << 29)
-#define SR_CONF_MASK 0x1fffffff
+/** Configuration capabilities. */
+enum sr_configcap {
+ /** Value can be read. */
+ SR_CONF_GET = (1UL << 31),
+ /** Value can be written. */
+ SR_CONF_SET = (1UL << 30),
+ /** Possible values can be enumerated. */
+ SR_CONF_LIST = (1UL << 29),
+};
/** Configuration keys */
enum sr_configkey {
/** The device can act as a scale. */
SR_CONF_SCALE,
+ /** The device can act as a function generator. */
+ SR_CONF_SIGNAL_GENERATOR,
+
+ /** The device can measure power. */
+ SR_CONF_POWERMETER,
+
+ /**
+ * The device can switch between multiple sources, e.g. a relay actuator
+ * or multiplexer.
+ */
+ SR_CONF_MULTIPLEXER,
+
/* Update sr_key_info_config[] (hwdriver.c) upon changes! */
/*--- Driver scan options -------------------------------------------*/
*/
SR_CONF_MODBUSADDR,
+ /**
+ * User specified forced driver attachment to unknown devices.
+ *
+ * By design the interpretation of the string depends on the
+ * specific driver. It typically would be either a replacement
+ * '*IDN?' response value, or a sub-driver name. But could also
+ * be anything else and totally arbitrary.
+ */
+ SR_CONF_FORCE_DETECT,
+
+ /**
+ * Override builtin probe names from user specs.
+ *
+ * Users may want to override the names which are assigned to
+ * probes during scan (these usually match the vendor's labels
+ * on the device). This avoids the interactive tedium of
+ * changing channel names after device creation and before
+ * protocol decoder attachment. Think of IEEE488 recorders or
+ * parallel computer bus loggers. The scan option eliminates
+ * the issue of looking up previously assigned names before
+ * renaming a channel (see sigrok-cli -C), which depends on
+ * the device as well as the application, and is undesirable.
+ * The scan option is limited to those drivers which implement
+ * support for it, but works identically across those drivers.
+ *
+ * The value is a string, either a comma separated list of
+ * probe names, or an alias for a typical set of names.
+ */
+ SR_CONF_PROBE_NAMES,
+
/* Update sr_key_info_config[] (hwdriver.c) upon changes! */
/*--- Device (or channel group) configuration -----------------------*/
/** Coupling. */
SR_CONF_COUPLING,
- /** Trigger matches. */
+ /** Trigger matches. */
SR_CONF_TRIGGER_MATCH,
/** The device supports setting its sample interval, in ms. */
/** Number of horizontal divisions, as related to SR_CONF_TIMEBASE. */
SR_CONF_NUM_HDIV,
- /** Number of vertical divisions, as related to SR_CONF_VDIV. */
+ /** Number of vertical divisions, as related to SR_CONF_VDIV. */
SR_CONF_NUM_VDIV,
- /** Sound pressure level frequency weighting. */
+ /** Sound pressure level frequency weighting. */
SR_CONF_SPL_WEIGHT_FREQ,
- /** Sound pressure level time weighting. */
+ /** Sound pressure level time weighting. */
SR_CONF_SPL_WEIGHT_TIME,
- /** Sound pressure level measurement range. */
+ /** Sound pressure level measurement range. */
SR_CONF_SPL_MEASUREMENT_RANGE,
/** Max hold mode. */
* Channel regulation
* get: "CV", "CC" or "UR", denoting constant voltage, constant current
* or unregulated.
+ * "CC-" denotes a power supply in current sink mode (e.g. HP 66xxB).
+ * "" is used when there is no regulation, e.g. the output is disabled.
*/
SR_CONF_REGULATION,
/** Over-temperature protection (OTP) active. */
SR_CONF_OVER_TEMPERATURE_PROTECTION_ACTIVE,
- /* Update sr_key_info_config[] (hwdriver.c) upon changes! */
+ /** Under-voltage condition. */
+ SR_CONF_UNDER_VOLTAGE_CONDITION,
- /*--- Special stuff -------------------------------------------------*/
+ /** Under-voltage condition active. */
+ SR_CONF_UNDER_VOLTAGE_CONDITION_ACTIVE,
+
+ /** Trigger level. */
+ SR_CONF_TRIGGER_LEVEL,
+
+ /** Under-voltage condition threshold. */
+ SR_CONF_UNDER_VOLTAGE_CONDITION_THRESHOLD,
+
+ /**
+ * Which external clock source to use if the device supports
+ * multiple external clock channels.
+ */
+ SR_CONF_EXTERNAL_CLOCK_SOURCE,
+
+ /** Offset of a source without strictly-defined MQ. */
+ SR_CONF_OFFSET,
+
+ /** The device supports setting a pattern for the logic trigger. */
+ SR_CONF_TRIGGER_PATTERN,
+
+ /** High resolution mode. */
+ SR_CONF_HIGH_RESOLUTION,
+
+ /** Peak detection. */
+ SR_CONF_PEAK_DETECTION,
+
+ /** Logic threshold: predefined levels (TTL, ECL, CMOS, etc). */
+ SR_CONF_LOGIC_THRESHOLD,
+
+ /** Logic threshold: custom numerical value. */
+ SR_CONF_LOGIC_THRESHOLD_CUSTOM,
+
+ /** The measurement range of a DMM or the output range of a power supply. */
+ SR_CONF_RANGE,
+
+ /** The number of digits (e.g. for a DMM). */
+ SR_CONF_DIGITS,
+
+ /** Phase of a source signal. */
+ SR_CONF_PHASE,
+
+ /** Duty cycle of a source signal. */
+ SR_CONF_DUTY_CYCLE,
- /** Scan options supported by the driver. */
- SR_CONF_SCAN_OPTIONS = 40000,
+ /**
+ * Current power.
+ * @arg type: double
+ * @arg get: get measured power
+ */
+ SR_CONF_POWER,
+
+ /**
+ * Power target.
+ * @arg type: double
+ * @arg get: get power target
+ * @arg set: change power target
+ */
+ SR_CONF_POWER_TARGET,
+
+ /**
+ * Resistance target.
+ * @arg type: double
+ * @arg get: get resistance target
+ * @arg set: change resistance target
+ */
+ SR_CONF_RESISTANCE_TARGET,
+
+ /* Update sr_key_info_config[] (hwdriver.c) upon changes! */
- /** Device options for a particular device. */
- SR_CONF_DEVICE_OPTIONS,
+ /*--- Special stuff -------------------------------------------------*/
/** Session filename. */
- SR_CONF_SESSIONFILE,
+ SR_CONF_SESSIONFILE = 40000,
/** The device supports specifying a capturefile to inject. */
SR_CONF_CAPTUREFILE,
/** The device supports setting a probe factor. */
SR_CONF_PROBE_FACTOR,
+ /** Number of powerline cycles for ADC integration time. */
+ SR_CONF_ADC_POWERLINE_CYCLES,
+
/* Update sr_key_info_config[] (hwdriver.c) upon changes! */
/*--- Acquisition modes, sample limiting ----------------------------*/
struct sr_dev_driver {
/* Driver-specific */
/** Driver name. Lowercase a-z, 0-9 and dashes (-) only. */
- char *name;
+ const char *name;
/** Long name. Verbose driver name shown to user. */
- char *longname;
+ const char *longname;
/** API version (currently 1). */
int api_version;
/** Called when driver is loaded, e.g. program startup. */
/** Close device */
int (*dev_close) (struct sr_dev_inst *sdi);
/** Begin data acquisition on the specified device. */
- int (*dev_acquisition_start) (const struct sr_dev_inst *sdi,
- void *cb_data);
+ int (*dev_acquisition_start) (const struct sr_dev_inst *sdi);
/** End data acquisition on the specified device. */
- int (*dev_acquisition_stop) (struct sr_dev_inst *sdi,
- void *cb_data);
+ int (*dev_acquisition_stop) (struct sr_dev_inst *sdi);
/* Dynamic */
/** Device driver context, considered private. Initialized by init(). */