Difference between revisions of "RockyLogic Ant8"

From sigrok
Jump to navigation Jump to search
(DIY Ant8 probe cable)
Line 48: Line 48:
* 10-pin colored ribbon cable, such as [http://www.reichelt.de/Flachbandkabel/AWG-28-10F-3M/index.html?;ACTION=3;LA=2;ARTICLE=47668;GROUPID=3328;artnr=AWG+28-10F+3M this one].
* 10-pin colored ribbon cable, such as [http://www.reichelt.de/Flachbandkabel/AWG-28-10F-3M/index.html?;ACTION=3;LA=2;ARTICLE=47668;GROUPID=3328;artnr=AWG+28-10F+3M this one].
** The colors match the one shipped with the Ant8 (white, gray, purple, blue, green, yellow, orange, red, brown) if you remove the 10th (black) lead.
** The colors match the one shipped with the Ant8 (white, gray, purple, blue, green, yellow, orange, red, brown) if you remove the 10th (black) lead.
* A "SUB-D" connector where you can attach the ribbon cable, such as [http://www.reichelt.de/SUB-D-Flachbandverbinder/D-SUB-BU-09FB/index.html?;ACTION=3;LA=2;ARTICLE=6951;GROUPID=3204;artnr=D-SUB+BU+09FB this one], which we'll cut into two halves to get 10 female connectors (only 9 needed).
* A "SUB-D" connector where you can attach the ribbon cable, such as [http://www.reichelt.de/SUB-D-Flachbandverbinder/D-SUB-BU-09FB/index.html?;ACTION=3;LA=2;ARTICLE=6951;GROUPID=3204;artnr=D-SUB+BU+09FB this one].
* 5 female-female jumper wires, such as [http://www.komputer.de/zen/index.php?main_page=product_info&cPath=31&products_id=77 these ones].
* 5 female-female jumper wires, such as [http://www.komputer.de/zen/index.php?main_page=product_info&cPath=31&products_id=77 these ones], which we'll cut into two halves to get 10 female connectors (only 9 needed).
* 9 short pieces of heat-shrink tubing.
* 9 short pieces of heat-shrink tubing.
* 9 E-Z Hook grippers/hooks to attach to the cable.
* 9 E-Z Hook grippers/hooks to attach to the cable.
<gallery>
File:Diy rockylogic ant8 cable connector.jpg
File:Diy rockylogic ant8 cable ribbon cable.jpg
File:Diy rockylogic ant8 cable cable connected.jpg
File:Diy rockylogic ant8 cable jumper wires.jpg
File:Diy rockylogic ant8 cable jumper wires cut.jpg
File:Diy rockylogic ant8 cable heat shrink tubing.jpg
File:Diy rockylogic ant8 cable prepare heatshrink tubing.jpg
File:Diy rockylogic ant8 cable solder jumper wires.jpg
File:Diy rockylogic ant8 cable heated up.jpg
File:Diy rockylogic ant8 cable finished with ezhooks.jpg
</gallery>

Revision as of 01:45, 23 December 2011

The RockyLogic Ant8 is an 8-channel, 500MHz logic analyzer.

See RockyLogic_Ant8/Info for more details (such as lsusb -vvv output) about the device.

Components

  • Xilinx Spartan-II XC2S30 VQ100AMS0341 (FPGA; 13,824 total distributed RAM bits, 24K total block RAM)
  • Xilinx XC9572XL VQ44BMN0345 10C (CPLD; 10ns pin-to-pin logic delays)
  • FTDI FT245BM (USB FIFO device)
  • IDT ICS501M (clock multiplier)
  • Atmel AT93C66 (4kB, three-wire serial EEPROM)
  • ON Semiconductor (On) HC00A PGZI (quad 2-input NAND gate)
  • National/TI LP2989 (marking: 33AB 2989 IM-2.5) (micropower/low-noise, 500mA ultra low-dropout regulator)
  • 20MHz crystal (for the FPGA)

Photos

See also this flickr set for more PCB photos of the device.

Status

Support for this device is currently being worked on.

Protocol

See the Ant18e wiki page for a description of the Ant8/Ant16/Ant18e protocol.

DIY Ant8 probe cable

The Ant8 cable shipped with the device doesn't have the best quality probes/hooks, but you can easily make your own cable where you can attach the better-quality E-Z Hooks.

Requirements:

  • 10-pin colored ribbon cable, such as this one.
    • The colors match the one shipped with the Ant8 (white, gray, purple, blue, green, yellow, orange, red, brown) if you remove the 10th (black) lead.
  • A "SUB-D" connector where you can attach the ribbon cable, such as this one.
  • 5 female-female jumper wires, such as these ones, which we'll cut into two halves to get 10 female connectors (only 9 needed).
  • 9 short pieces of heat-shrink tubing.
  • 9 E-Z Hook grippers/hooks to attach to the cable.