Difference between revisions of "Noname XL-LOGIC16-100M"
Uwe Hermann (talk | contribs) (→Photos) |
|||
| Line 20: | Line 20: | ||
See [[Noname XL-LOGIC16-100M/Info]] for more details (such as '''lsusb -v''' output) about the device. | See [[Noname XL-LOGIC16-100M/Info]] for more details (such as '''lsusb -v''' output) about the device. | ||
== Variants in same case == | |||
The 2015-1-8 version of the [[Mcupro_Logic16_clone]] comes in the same case as this device. Unlike this device, the mcupro version works with sigrok! | |||
== Hardware == | == Hardware == | ||
Revision as of 02:52, 6 June 2015
 | |
| Status | planned |
|---|---|
| Source code | saleae-logic16 |
| Channels | 3/6/9/16 |
| Samplerate | 100/50/32/16MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.9V — 6V |
| Threshold voltage |
configurable: for 1.8V to 3.6V systems: VIH=1.4V, VIL=0.7V for 5V systems: VIH=3.6V, VIL=1.4V |
| Memory | none |
| Compression | yes |
| Website | aliexpress.com |
The Noname XL-LOGIC16-100M is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate.
It is labelled and sold as a Saleae Logic16 clone, and comes with "modified" Saleae Logic software on a CD-ROM.
See Noname XL-LOGIC16-100M/Info for more details (such as lsusb -v output) about the device.
Variants in same case
The 2015-1-8 version of the Mcupro_Logic16_clone comes in the same case as this device. Unlike this device, the mcupro version works with sigrok!
Hardware
A single Phillips head screw holds the case together. Most notable are the complete lack of test points or programming headers! There are some unpopulated resistor/capacitor pairs on the backside.
- FPGA: Xilinx Spartan-3A XC3S200A, 200K gates (datasheeet)
- USB interface chip: Cypress CY7C68013A-56PVXC (FX2LP) (datasheet)
- I2C EEPROM: 2Kbit Atmel 24C02B (markings: "ATMEL317 24C02BN SU27 D") (datasheet)
- 16-Bit 2.5V to 3.3V/3.3V to 5V level shifting transceiver with 3-state outputs: TI SN74ALVC164245 (datasheet)
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3 (datasheet, older datasheet)
- 1.2V voltage regulator: Advanced Monolithic Systems AMS1117-1.2 (datasheet, older datasheet)
- Crystal: 24.000
Three LEDs (USB/green, COM/blue, and RUN/red) are on the board.
Photos
Photos from another unit:
Photos from yet another unit (with JTAG and other resistor values):
Photos from yet another unit (with black case):
Firmware
You can use the sigrok-fwextract-saleae-logic16 tool to extract (from the "Logic" Linux binary) the FX2 firmware and the FPGA bitstreams, exactly as for a real Saleae Logic16. Note, the md5sum of the FX2 firmware is identical to the original Saleae firmware, but the FPGA bitstreams are different. Attempting to connect to this device with the "modified" FPGA bitstream, which _works_ with the vendor supplied "modified" Logic software fails to load in sigrok, with a FPGA version mismatch. The FX2 firmware loads successfully, at least in as much as the LED blinks a heartbeat pattern as expected.