Difference between revisions of "Noname LHT00SU1"
Uwe Hermann (talk | contribs) m |
Uwe Hermann (talk | contribs) |
||
| Line 5: | Line 5: | ||
| source_code_dir = fx2lafw | | source_code_dir = fx2lafw | ||
| channels = 8 + 1 | | channels = 8 + 1 | ||
| samplerate = 24MHz | | samplerate = 8ch @ 24MHz, 8+1ch @ 12MHz | ||
| samplerate_state = — | | samplerate_state = — | ||
| triggers = none (SW-only) | | triggers = none (SW-only) | ||
| Line 15: | Line 15: | ||
}} | }} | ||
The '''Noname LHT00SU1''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time). | The '''Noname LHT00SU1''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth). | ||
It is a clone of the [[CWAV USBee AX-Pro]]. | It is a clone of the [[CWAV USBee AX-Pro]]. | ||
| Line 24: | Line 24: | ||
== Hardware == | == Hardware == | ||
There's a jumper on the PCB which write-protects the I²C EEPROM when set (it ships in that state) by keeping the WP pin at 3.3V. | There's a jumper on the PCB which write-protects the I²C EEPROM when set (it ships in that state) by keeping the WP pin at 3.3V. | ||
Revision as of 23:49, 17 September 2017
 | |
| Status | supported |
|---|---|
| Source code | fx2lafw |
| Channels | 8 + 1 |
| Samplerate | 8ch @ 24MHz, 8+1ch @ 12MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage |
Digital: 0V — +5.3V Analog: ±10V |
| Threshold voltage | Fixed: VIH=1.4V, VIL=0.8V |
| Memory | none |
| Compression | none |
| Website | aliexpress.com |
The Noname LHT00SU1 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, with 1 additional analog channel (theoretically 2, but only one of them can be used at a time; 3MHz analog bandwidth).
It is a clone of the CWAV USBee AX-Pro.
In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.
See Noname LHT00SU1/Info for some more details (such as lsusb -v output) on the device.
Hardware
There's a jumper on the PCB which write-protects the I²C EEPROM when set (it ships in that state) by keeping the WP pin at 3.3V.
Photos
LTH00SU1-V5.0:
Package contents
Device, top
Device, bottom
PCB, top
PCB, bottom
Cypress FX2
TLC5510I
Unknown SO8
LM358
HEF4051BT
Bochen 3296
AMS1117-3.3
24C02N
Protocol
Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.
Resources
- raspberrypiwiki.com: LHT00SU1_Virtual_Oscilloscope_SKU:412961 (info and software download)