Difference between revisions of "KingST KQS3506-LA16100"

From sigrok
Jump to navigation Jump to search
(2 intermediate revisions by 2 users not shown)
Line 19: Line 19:
This is a clone of the [[Saleae Logic16]].
This is a clone of the [[Saleae Logic16]].


See [[KingST KQS3506-LA16100/Info]] for more details (such as '''lsusb -vvv''' output) about the device.
See [[KingST KQS3506-LA16100/Info]] for more details (such as '''lsusb -v''' output) about the device.


== Hardware ==
== Hardware ==
Line 213: Line 213:
File:Kingst kqs3506 la16100 pcb v6 top.jpg|<small>PCB, top</small>
File:Kingst kqs3506 la16100 pcb v6 top.jpg|<small>PCB, top</small>
File:Kingst kqs3506 la16100 pcb v6 bottom.jpg|<small>PCB, bottom</small>
File:Kingst kqs3506 la16100 pcb v6 bottom.jpg|<small>PCB, bottom</small>
File:Kingst kqs3506 la16100 schematic v6.png|<small>Schematic drawn from PCB</small>
</gallery>
</gallery>


Line 227: Line 228:
[[Category:Device]]
[[Category:Device]]
[[Category:Logic analyzer]]
[[Category:Logic analyzer]]
[[Category:In progress]]
[[Category:Supported]]

Revision as of 15:24, 23 November 2014

KingST KQS3506-LA16100
Kingst kqs3506 la16100.png
Status supported
Source code saleae-logic16
Channels 3/6/9/16
Samplerate 100/50/32/16MHz
Samplerate (state)
Triggers none (SW-only)
Min/max voltage -0.9V — 6V
Threshold voltage configurable:
for 1.8V to 3.6V systems: VIH=1.4V, VIL=0.7V
for 5V systems: VIH=3.6V, VIL=1.4V
Memory none
Compression yes
Website taobao.com

The KingST KQS3506-LA16100 is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels).

This is a clone of the Saleae Logic16.

See KingST KQS3506-LA16100/Info for more details (such as lsusb -v output) about the device.

Hardware

Pinouts and connections:

I2C EEPROM:

The Microchip 24LC02B is connected to the Cypress FX2. The WP pin of the EEPROM can be jumpered to low or high, in order to write-protect it (or not). The address pins (A0-A2) are all connected to GND, which makes the I2C slave address of the EEPROM 0x50.

(GND) A0 1-   O -8 VCC (3.3V)
(GND) A1 2- -7 WP (jumper W2)
(GND) A2 3- -6 SCL (FX2 SCL)
GND 4- -5 SDA (FX2 SDA)

CLPD:

The Altera EPM3032A JTAG pins are available on the J3 pin header.

1 2 3 4 5 6 7 8 9 10 11
JTAG TDI I/O (FX2 PA7) I/O (FX2 PA6) GND I/O (FX2 PA5) I/O (FX2 PA4) JTAG TMS I/O (FX2 PA3) VCC I/O (FX2 PA2) GND
12 13 14 15 16 17 18 19 20 21 22
I/O (FX2 PA1) I/O (FX2 PA0) I/O (FPGA PROG_B) I/O (FPGA 94, IO_L05N_0) GND VCC I/O (FPGA 85, IO_L03P_0) I/O (FX2 CTL2) I/O (FX2 CTL1) I/O (FX2 CTL0) I/O (FPGA 51, DIN/MISO)
23 24 25 26 27 28 29 30 31 32 33
I/O (NC?) GND I/O (FPGA 97, IP0) JTAG TCK I/O (FPGA 53, CCLK) I/O (NC?) VCC GND I/O (FPGA 3, IO_L01P_3) JTAG TDO I/O (NC?)
34 35 36 37 38 39 40 41 42 43 44
I/O (NC?) I/O (NC?) GND I/O (NC?) I/O (NC?) I/O (NC?) I/O (NC?) VCC I/O (NC?) I/O (NC?) I/O (NC?)

JTAG header (CPLD):

The J3 pin header is a JTAG connector wired to the CPLD (it is not additionally wired to the FPGA in a JTAG chain). The pins are (from left to right):

1 2 3 4 5 6
TMS TDI TCK TDO GND 3.3V

Photos

Revision 5.0:

Revision 6.0:

Protocol

See Saleae_Logic16#Protocol.

Resources