Difference between revisions of "DreamSourceLab DSLogic Pro"
Jump to navigation
Jump to search
(Page creation) |
Uwe Hermann (talk | contribs) m (Add correct source code directory.) |
||
| (8 intermediate revisions by 3 users not shown) | |||
| Line 2: | Line 2: | ||
| image = [[File:DSLogic.png|180px]] | | image = [[File:DSLogic.png|180px]] | ||
| name = DreamSourceLab DSLogic Pro | | name = DreamSourceLab DSLogic Pro | ||
| status = | | status = supported | ||
| source_code_dir = | | source_code_dir = dreamsourcelab-dslogic | ||
| channels = 1-16 | | channels = 1-16 | ||
| samplerate = 400MHz(4ch), 200MHz(8ch), 100MHz(16ch) | | samplerate = 400MHz(4ch), 200MHz(8ch), 100MHz(16ch) | ||
| Line 15: | Line 15: | ||
}} | }} | ||
The '''DreamSourceLab DSLogic Pro''' is a 16-channel USB-based logic analyzer, with sampling rates up to 400MHz (when using only 4 channels). This differs slightly from the original DSLogic product in its configurable threshold voltage and different PCB layout. | The '''DreamSourceLab DSLogic Pro''' is a 16-channel USB-based logic analyzer, with sampling rates up to 400MHz (when using only 4 channels). This differs slightly from the original DSLogic product in its configurable threshold voltage and different PCB layout. DreamSourceLab doesn't make the distinction between these two products very clear on their website. | ||
See [[DreamSourceLab DSLogic Pro/Info]] for more details (such as '''lsusb -v''' output) about the device. | See [[DreamSourceLab DSLogic Pro/Info]] for more details (such as '''lsusb -v''' output) about the device. | ||
| Line 32: | Line 32: | ||
<gallery> | <gallery> | ||
File:DSLogic.png|<small>Device, top</small> | |||
File:DSLogic connector.jpg|<small>Probe connector</small> | |||
File:DSLogic USB.jpg|<small>USB connector</small> | |||
File:DSLogic Pro PCB front.jpg|<small>PCB, top</small> | |||
File:DSLogic Pro PCB back.jpg|<small>PCB, bottom</small> | |||
</gallery> | </gallery> | ||
== Firmware == | |||
See [[DreamSourceLab DSLogic#Firmware]]. | |||
== Resources == | == Resources == | ||
| Line 44: | Line 53: | ||
[[Category:Device]] | [[Category:Device]] | ||
[[Category:Logic analyzer]] | [[Category:Logic analyzer]] | ||
[[Category: | [[Category:Supported]] | ||
Revision as of 20:11, 11 November 2017
 | |
| Status | supported |
|---|---|
| Source code | dreamsourcelab-dslogic |
| Channels | 1-16 |
| Samplerate | 400MHz(4ch), 200MHz(8ch), 100MHz(16ch) |
| Samplerate (state) | 50MHz |
| Triggers | high, low, rising, falling, edge, multi-stage triggers |
| Min/max voltage | -0.6V — 6V |
| Threshold voltage | configurable: 0-5V (0.1V increments) |
| Memory | 32MByte (2MByte/ch) |
| Compression | yes |
| Website | dreamsourcelab.com |
The DreamSourceLab DSLogic Pro is a 16-channel USB-based logic analyzer, with sampling rates up to 400MHz (when using only 4 channels). This differs slightly from the original DSLogic product in its configurable threshold voltage and different PCB layout. DreamSourceLab doesn't make the distinction between these two products very clear on their website.
See DreamSourceLab DSLogic Pro/Info for more details (such as lsusb -v output) about the device.
Hardware
- Xilinx XC6SLX9 U2: Spartan-6 FPGA (TQG144BIV13337)
- Micron MT48LC16M16A2P-6A U29: 32MB SDRAM (IC SDRAM 256MBIT 167MHZ TSOP)
- Cypress CY7C68013A U33: FX2 USB interface chip (IC MCU USB PERIPH HI SPD 56SSOP)
- Serial EEPROM 16Kbit U4: ATMLH348 16CM Y 3X3098, I2C/2Wire Serial EEPROM 16Kbit (2048x8) ATMEL AT24C16C
- ESD Protection U9,10,11,12,13,14: D234 ESD Protection CM1213A-04S7 TVS DIODE 3.3VWM 10VC SC746
- Adjustable 500mA LDO U3: Adjustable (configured for 3.3V) 600mA 2MHz Step Down DC-DC Converter MIC5209YM
- 1.2V 600mA LDO U31: SBPB 1.2V 600mA 2MHz Step Down DC-DC Converter LM3671MF-1.2/NOPB
Photos
Device, top
Probe connector
USB connector
PCB, top
PCB, bottom
Firmware
See DreamSourceLab DSLogic#Firmware.