Difference between revisions of "DreamSourceLab DSLogic"

From sigrok
Jump to navigation Jump to search
(Remove dead links)
(9 intermediate revisions by 4 users not shown)
Line 3: Line 3:
| name            = DreamSourceLab DSLogic
| name            = DreamSourceLab DSLogic
| status          = supported
| status          = supported
| source_code_dir  = fx2lafw
| source_code_dir  = dreamsourcelab-dslogic
| channels        = 1-16
| channels        = 1-16
| samplerate      = 400MHz(4ch), 200MHz(8ch), 100MHz(16ch)
| samplerate      = 400MHz(4ch), 200MHz(8ch), 100MHz(16ch)
Line 38: Line 38:
File:DSLogic PCB back.jpg|<small>PCB, bottom</small>
File:DSLogic PCB back.jpg|<small>PCB, bottom</small>
</gallery>
</gallery>
== Firmware ==
In order to use this device with [[libsigrok]] the [https://github.com/DreamSourceLab/DSView/raw/886b847c21c606df3138ce7ad8f8e8c363ee758b/DSView/res vendor firmare and bitstream files] (v0.97) are required.
The easiest method to install those is to use the [http://sigrok.org/gitweb/?p=sigrok-util.git;a=blob;f=firmware/dreamsourcelab-dslogic/sigrok-fwextract-dreamsourcelab-dslogic sigrok-fwextract-dreamsourcelab-dslogic] script. It will download the correct files, rename them to the correct filenames as expected by libsigrok and install them.
'''Example usage''':
<small>
$ '''PREFIX=$HOME/sr ./sigrok-fwextract-dreamsourcelab-dslogic'''
</small>
This will install the files into '''$HOME/sr/share/sigrok-fimware'''. Without '''PREFIX''', the files will be installed into '''/usr/local/share/sigrok-firmware''' by default.
If you want to avoid using the script, you can manually download and rename the files (but check [http://sigrok.org/gitweb/?p=sigrok-util.git;a=blob;f=firmware/dreamsourcelab-dslogic/sigrok-fwextract-dreamsourcelab-dslogic the script] for the correct filenames).
After firmware is correctly installed, you can see if it's worked like this:
<pre>
sigrok-cli --driver=dreamsourcelab-dslogic -l 5 --scan
</pre>
You should see the driver detected and uploading the firmware
<pre>
sr: [00:00.014417] resource: Opened '/usr/local/share/sigrok-firmware/dreamsourcelab-dslogic-basic-fx2.fw'.
sr: [00:00.014454] ezusb: Uploading firmware 'dreamsourcelab-dslogic-basic-fx2.fw'.
sr: [00:00.014972] ezusb: Uploaded 4096 bytes.
sr: [00:00.015481] ezusb: Uploaded 4024 bytes.
sr: [00:00.015492] ezusb: Firmware upload done.
sr: [00:00.015497] ezusb: setting CPU reset mode off...
sr: [00:00.015606] hwdriver: Scan found 1 devices (dreamsourcelab-dslogic).
The following devices were found:
dreamsourcelab-dslogic - DreamSourceLab DSLogic Basic with 16 channels: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
sr: [00:00.015691] hwdriver: Cleaning up all drivers.
</pre>
== Capabilities ==
Use --show to fetch the current available options
<pre>
sigrok-cli --driver=dreamsourcelab-dslogic --show
</pre>
This example shows how to use sigrok-cli to capture 1k samples at 500khz on channels 0 and 1, with voltage threshold of 2.5v
<pre>
sigrok-cli -C 0,1 --driver=dreamsourcelab-dslogic  -c "samplerate=500k:voltage_threshold=2.5-2.5" --samples 1k
</pre>
This example shows continuous capture (requires the device config to include 'continuous=on')
<pre>
sigrok-cli -c "samplerate=10k:voltage_threshold=2.5-2.5:continuous=on" --driver=dreamsourcelab-dslogic --continuous
</pre>


== Resources ==
== Resources ==


* [http://www.dreamsourcelab.com Vendor website]
* [http://www.dreamsourcelab.com Vendor website]
* [http://www.dreamsourcelab.com/wiki/index.php Vendor wiki]
* [http://www.dreamsourcelab.com/forum/index.php Vendor forum]
* [http://www.dreamsourcelab.com/techspec.html Device specs]
* [https://www.kickstarter.com/projects/dreamsourcelab/dslogic-multifunction-instruments-for-everyone Kickstarter page]
* [https://www.kickstarter.com/projects/dreamsourcelab/dslogic-multifunction-instruments-for-everyone Kickstarter page]



Revision as of 21:58, 10 October 2018

DreamSourceLab DSLogic
DSLogic.png
Status supported
Source code dreamsourcelab-dslogic
Channels 1-16
Samplerate 400MHz(4ch), 200MHz(8ch), 100MHz(16ch)
Samplerate (state) 50MHz
Triggers high, low, rising, falling, edge, multi-stage triggers
Min/max voltage -0.6V — 6V
Threshold voltage configurable: 3.3V, 5V
Memory 32MByte (2MByte/ch)
Compression no
Website dreamsourcelab.com

The DreamSourceLab DSLogic is a 16-channel USB-based logic analyzer, with sampling rates up to 400MHz (when using only 4 channels).

See DreamSourceLab DSLogic/Info for more details (such as lsusb -v output) about the device.

Hardware

Photos

Firmware

In order to use this device with libsigrok the vendor firmare and bitstream files (v0.97) are required.

The easiest method to install those is to use the sigrok-fwextract-dreamsourcelab-dslogic script. It will download the correct files, rename them to the correct filenames as expected by libsigrok and install them.

Example usage:

$ PREFIX=$HOME/sr ./sigrok-fwextract-dreamsourcelab-dslogic

This will install the files into $HOME/sr/share/sigrok-fimware. Without PREFIX, the files will be installed into /usr/local/share/sigrok-firmware by default.

If you want to avoid using the script, you can manually download and rename the files (but check the script for the correct filenames).

After firmware is correctly installed, you can see if it's worked like this:

sigrok-cli --driver=dreamsourcelab-dslogic -l 5 --scan

You should see the driver detected and uploading the firmware

sr: [00:00.014417] resource: Opened '/usr/local/share/sigrok-firmware/dreamsourcelab-dslogic-basic-fx2.fw'.
sr: [00:00.014454] ezusb: Uploading firmware 'dreamsourcelab-dslogic-basic-fx2.fw'.
sr: [00:00.014972] ezusb: Uploaded 4096 bytes.
sr: [00:00.015481] ezusb: Uploaded 4024 bytes.
sr: [00:00.015492] ezusb: Firmware upload done.
sr: [00:00.015497] ezusb: setting CPU reset mode off...
sr: [00:00.015606] hwdriver: Scan found 1 devices (dreamsourcelab-dslogic).
The following devices were found:
dreamsourcelab-dslogic - DreamSourceLab DSLogic Basic with 16 channels: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
sr: [00:00.015691] hwdriver: Cleaning up all drivers.

Capabilities

Use --show to fetch the current available options

sigrok-cli --driver=dreamsourcelab-dslogic --show

This example shows how to use sigrok-cli to capture 1k samples at 500khz on channels 0 and 1, with voltage threshold of 2.5v

sigrok-cli -C 0,1 --driver=dreamsourcelab-dslogic  -c "samplerate=500k:voltage_threshold=2.5-2.5" --samples 1k

This example shows continuous capture (requires the device config to include 'continuous=on')

sigrok-cli -c "samplerate=10k:voltage_threshold=2.5-2.5:continuous=on" --driver=dreamsourcelab-dslogic --continuous

Resources