sigrok - User contributions [en]

UNI-T UT325/Info

2012-07-10T09:02:29Z

Phil:

== lsusb ==

This is Linux '''lsusb''' output:


$ '''lsusb -vvv'''
Bus 002 Device 002: ID '''1a86:e008 QinHeng Electronics HID-based serial adapater'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor '''0x1a86 QinHeng Electronics'''
idProduct '''0xe008 HID-based serial adapater'''
bcdDevice 11.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 '''Human Interface Device'''
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 37
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Device Status: 0x000a
(Bus Powered)
Remote Wakeup Enabled

UNI-T UT325/Info

2012-07-10T09:02:07Z

Phil:

=== lsusb ===

This is Linux '''lsusb''' output:


$ '''lsusb -vvv'''
Bus 002 Device 002: ID '''1a86:e008 QinHeng Electronics HID-based serial adapater'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor '''0x1a86 QinHeng Electronics'''
idProduct '''0xe008 HID-based serial adapater'''
bcdDevice 11.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 '''Human Interface Device'''
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 37
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Device Status: 0x000a
(Bus Powered)
Remote Wakeup Enabled

UNI-T UT325/Info

2012-07-10T09:01:01Z

Phil: Created page with "===Lsusb=== This is Linux '''lsusb''' output: $ '''lsusb -vvv''' Bus 002 Device 002: ID '''1a86:e008 QinHeng Electronics HID-based serial adapater''' Device Descr..."

===Lsusb===

This is Linux '''lsusb''' output:


$ '''lsusb -vvv'''
Bus 002 Device 002: ID '''1a86:e008 QinHeng Electronics HID-based serial adapater'''
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor '''0x1a86 QinHeng Electronics'''
idProduct '''0xe008 HID-based serial adapater'''
bcdDevice 11.00
iManufacturer 1
iProduct 2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 41
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 4
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 3 '''Human Interface Device'''
bInterfaceSubClass 0 No Subclass
bInterfaceProtocol 0 None
iInterface 0
HID Device Descriptor:
bLength 9
bDescriptorType 33
bcdHID 1.00
bCountryCode 0 Not supported
bNumDescriptors 1
bDescriptorType 34 Report
wDescriptorLength 37
Report Descriptors:
** UNAVAILABLE **
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0008 1x 8 bytes
bInterval 5
Device Status: 0x000a
(Bus Powered)
Remote Wakeup Enabled

UNI-T UT325

2012-07-09T19:17:58Z

Phil: Created page with "UNI-T UT325 The [http://www.uni-trend.com/UT325.html UNI-T UT325] is a logging thermometer with two thermocouple inputs and USB con..."

[[File:Uni-t ut325 front.jpg|thumb|right|UNI-T UT325]]

The [http://www.uni-trend.com/UT325.html UNI-T UT325] is a logging thermometer with two thermocouple inputs and USB connectivity. It supports K,J,T,E,R,S,N thermocouple types.

See [[UNI-T UT325/Info]] for more details about the device.

== Hardware ==

* TODO.

== Photos ==

<gallery>
File:Uni-t ut325 packaging.jpg
File:Uni-t ut325 perspective.jpg
File:Uni-t ut325 front.jpg
File:Uni-t ut325 top.jpg
File:Uni-t ut325 back wo bail.jpg
File:Uni-t ut325 back battery.jpg
File:Uni-t ut325 case open.jpg
File:Uni-t ut325 fpanel back.jpg
File:Uni-t ut325 pcb bottom.jpg
File:Uni-t ut325 pcb front w display.jpg
File:Uni-t ut325 pcb front.jpg
</gallery>

== Protocol ==

* TODO.

== Resources ==

* TODO.

Supported hardware

2012-07-09T18:56:36Z

Phil: /* Dataloggers */

sigrok is intended as a flexible, cross-platform, and '''hardware-independent''' software suite, i.e., it supports various devices from many different vendors.

Here is a list of currently supported devices (various stages of completeness) and devices we plan to support in the near future.

== Logic analyzers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

|-
| [[File:Saleae Logic.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Saleae Logic]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:Eeelec xla esla100.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[EE Electronics ESLA100]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:ASIX SIGMA.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[ASIX SIGMA|ASIX SIGMA/SIGMA2]] is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate, and with 256Mbit on-board memory.

|-
| [[File:Openbench logic sniffer front.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Openbench Logic Sniffer]] (OLS) is a USB-based (and FPGA-based), 32-channel logic analyzer with up to 100MHz sampling rate and advanced trigger functionality. It is a fully open source device — the circuit design, VHDL code for the FPGA, firmware for the PIC microcontroller and Java-based client software are all freely available. It uses the [http://dangerousprototypes.com/docs/The_Logic_Sniffer%27s_extended_SUMP_protocol extended SUMP protocol].

|-
| [[File:logic-shrimp-front.png|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Logic Shrimp]] is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate. It uses the [http://dangerousprototypes.com/docs/The_Logic_Sniffer%27s_extended_SUMP_protocol extended SUMP protocol].

|-
| [[File:Zeroplus Logic Cube.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[ZEROPLUS Logic Cube LAP-C]] (16032) is a USB-based, 16-channel logic analyzer with up to 100MHz sampling rate.

|-
| [[File:Chronovu la8 device.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [http://www.chronovu.com/ ChronoVu LA8] is a USB-based, 8-channel logic analyzer with up to 100MHz sampling rate.

|-
| [[File:Robomotic buglogic3.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Robomotic BugLogic 3]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:Robomotic minilogic.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Robomotic MiniLogic]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:Lcsoft-miniboard-front.png|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Lcsoft Mini Board]] is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:Braintechnology usb lps.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Braintechnology USB-LPS]] is a USB-based, 16-channel logic analyzer (and signal generator) with up to 24MHz sampling rate.

|-
| [[File:Cwav usbee sx.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[CWAV USBee SX]] is a USB-based, 8-channel logic analyzer (and signal generator) with up to 24MHz sampling rate.

|-
| [[File:ARMFLY MINI LOGIC PCB.JPG|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[ARMFLY Mini-Logic]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:Braintechnology usb interface v2x pcb front.jpg|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[Braintechnology USB Interface V2.x]] is a Cypress FX2 eval board, which can be used as USB-based, 16-channel logic analyzer with up to 24MHz sampling rate.

|-
| [[File:Buspirate v3 front.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[Buspirate|Buspirate v3]] is a USB-based, 5-channel logic analyzer with up to 1MHz sampling rate. It uses the [http://dangerousprototypes.com/docs/The_Logic_Sniffer%27s_extended_SUMP_protocol extended SUMP protocol]. The Buspirate supports a logic analyzer mode and can thus be used for sample captures, however only at low speeds.

|-
| [[File:Ant18e_closed.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[RockyLogic Ant18e]] is a USB-based, 18-channel logic analyzer with up to 1GHz sampling rate.

|-
| [[File:Rockylogic ant8 device.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[RockyLogic Ant8]] is a USB-based, 8-channel logic analyzer with up to 500MHz sampling rate.

|-
| [[File:Ikalogic scanalogic2 device with probes.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Ikalogic SCANALOGIC-2 PRO]] is a USB-based, 4-channel logic analyzer with up to 20MHz sampling rate.

|-
| [[File:Microchip pickit2 device front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Microchip PICkit2]] is a USB-based, 3-channel logic analyzer with up to 1MHz sampling rate. The PICkit2 is actually a programmer/debugger for PIC microcontrollers, but it can also be used as logic analyzer.

|-
| [[File:Minila mockup.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[MiniLA Mockup]] is a USB-based, 32-channel logic analyzer with up to 100MHz sampling rate.

|-
| [[File:Acute_pkla1216_front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Acute PKLA-1216]] is a USB-based, 16-channel logic analyzer with up to 200MHz sampling rate.

|-
| [[File:Saleae_Logic16_bottom.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Saleae Logic16]] is a USB-based, 16-channel logic analyzer with 100/50/25/12.5MHz sampling rate (at 2/4/8/16 enabled channels).

|-
| [[File:Intronix Logicport.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Intronix Logicport LA1034]] is a USB-based (and FPGA-based), 34-channel logic analyzer with up to 500MHz sampling rate.

|}

== Mixed-signal devices ==

Devices which can be used as both logic analyzer and oscilloscopes.

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

|-
| [[File:AX-Pro.JPG|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[ARMFLY AX-Pro]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.

'''Note:''' Only the logic analyzer functionality is supported so far, analog support is work in progress.

|-
| [[File:Esla201a.JPG|100px|left]]
| bgcolor="lime" align="center" | [[File:Nuvola OK.png|16px]] supported
| style="vertical-align: top" | The [[EE Electronics ESLA201A]] is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate, and with 2 additional analog channels.

'''Note:''' Only the logic analyzer functionality is supported so far, analog support is work in progress.

|-
| [[File:Link Instruments MSO-19 front.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[Link Instruments MSO-19‎]] is a USB-based, 1-channel 2GSa/s oscilloscope, 8-channel 200MSa/s logic analyzer, 100MSa/s pattern generator and a [https://en.wikipedia.org/wiki/Time-domain_reflectometer TDR].

|-
| [[File:QA100 Full.JPG|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[QuantAsylum QA100]] is a USB-based, mixed-mode oscilloscope with 12 digital inputs, 2 analog, 1 trigger and 1 audio waveform generator.

|-
| [[File:Polabs poscope basic2 device top.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[PoLabs PoScope Basic2]] is a USB-based, 16-channel logic analyzer (plus oscilloscope, signal/pattern generator, and more) with up to 8MHz sampling rate.

|-
| [[File:Rigol_VS5202D_Full.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Rigol VS5202D]] is a USB-based, 2-channel analog oscilloscope (400MSa/S, 200MHz bandwidth) and 16-channel logic analyzer (200MHz sampling rate).

|-
| [[File:Agilent_MSO7104A.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Agilent MSO7104A]] is a standalone, 4-channel mixed-signal digital storage oscilloscope (1GHz bandwidth, 4GSa/s samplerate, 16-channel logic analyzer).

|}

== Oscilloscopes ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

|-
| [[File:Dso2090-case-top-small.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[Hantek DSO-2090]] is a USB-based, 2-channel oscilloscope with an analog bandwidth of 40MHz and 100MS/s sampling rate.

|-
| [[File:Hantek dso-5200a device front.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[Hantek DSO-5200A]] is a USB-based, 2-channel oscilloscope with an analog bandwidth of 200MHz and 250MS/s sampling rate.

|-
| [[File:Velleman pcsu1000 pcb front.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[Velleman PCSU1000]] is a USB-based, 2-channel oscilloscope with an analog bandwidth of 50MHz and 1GS/s sampling rate.

|-
| [[File:Picoscope 2203 front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Pico Technology PicoScope 2203]] is a USB-based, 2-channel oscilloscope with an analog bandwidth of 5MHz and 40/20MS/s sampling rate (1-/2-channel one-shot mode).

|}

== Multimeters ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

|-
| [[File:Mastech va18b device front.jpg|100px|left]]
| bgcolor="yellow" align="center" | [[File:Nuvola Orange.png|16px]] in progress
| style="vertical-align: top" | The [[Mastech VA18B]] a.k.a. '''V&A VA18B''' (V&A is a [http://www.mastech.com.cn/html/en/about-us.htm brand of Mastech]) is a 6000 counts, CAT II (1000V) handheld digital multimeter with USB connectivity.

|-
| [[File:Mastech mas345 device front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[MASTECH MAS345]] is a 3999 counts, CAT II handheld digital multimeter with RS232 connectivity.

|-
| [[File:Uni t ut61d device.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[UNI-T UT61D]] is a 6000 counts, CAT II (600V) / CAT III (300V) handheld digital multimeter with RS232 or USB connectivity.

|-
| [[File:Victor 70C.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Victor 70C]] is a 4000 counts, CAT II handheld digital multimeter with USB connectivity.

|-
| [[File:Voltcraft vc820 device.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Voltcraft VC-820]] is a 4000 counts, CAT III (1000V) / CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.

|-
| [[File:Voltcraft vc840 device front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Voltcraft VC-840]] is a 4000 counts, CAT IV (600V) handheld digital multimeter with RS232 or USB connectivity.

|}

== Dataloggers ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

|-
| [[File:Rding temper front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[RDing TEMPer]] is a USB-based temperature logger.

|-
| [[File:Rding temper gold device front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[RDing TEMPer Gold]] is a USB-based temperature logger.

|-
| [[File:Uni-t ut325 front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[UNI-T UT325]] is a dual thermocouple logging thermometer.

|}

== GPIB interfaces ==

{| border="0" class="alternategrey sigroktable"
|-
!Device
!Status
!Comments

|-
| [[File:GPIB-USB 82357B clone front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[GPIB-USB 82357B clone]] is a USB-based, hardware-implemented [[GPIB]] interface (a clone of the [http://www.home.agilent.com/agilent/product.jspx?ckey=851808&nid=-34193.426029.00&id=851808&cmpid=zzfind82357b Agilent 82357B USB/GPIB interface]).

|-
| [[File:Prologix-usb.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[Prologix GPIB-USB]] a USB-based, firmware-implemented [[GPIB]] interface.

|-
| [[File:NI GPIB-ENET front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[National Instruments GPIB-ENET]] is an Ethernet-based, hardware-implemented [[GPIB]] interface.

|-
| [[File:ICS 488-USB front.jpg|100px|left]]
| bgcolor="orange" align="center" | [[File:Nuvola Red.png|16px]] planned
| style="vertical-align: top" | The [[ICS 488-USB]] is a USB-based GPIB interface.

|}

== Potential other candidates ==

If you own any other logic analyzers (or oscilloscopes, multimeters, oscilloscopes, etc.) and want to add support for them in sigrok (or donate/lend devices to developers), please let us know. We're always happy to add more hardware support! Contact [mailto:bert@biot.com Bert Vermeulen] and [mailto:uwe@hermann-uwe.de Uwe Hermann] if you want to help out.

__FORCETOC__

File:Uni-t ut325 front.jpg

2012-07-09T18:55:33Z

Phil: Phil uploaded a new version of "File:Uni-t ut325 front.jpg"

File:Uni-t ut325 top.jpg

2012-07-09T18:30:46Z

Phil:

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 perspective.jpg

2012-07-09T18:30:23Z

Phil:

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 pcb front w display.jpg

2012-07-09T18:30:05Z

Phil:

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 pcb front.jpg

2012-07-09T18:29:31Z

Phil:

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 pcb bottom.jpg

2012-07-09T18:28:52Z

Phil:

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 packaging.jpg

2012-07-09T18:27:45Z

Phil:

File:Uni-t ut325 front.jpg

2012-07-09T18:27:17Z

Phil:

File:Uni-t ut325 fpanel back.jpg

2012-07-09T18:26:17Z

Phil: Back of the front panel

== Summary ==
Back of the front panel
== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 case open.jpg

2012-07-09T18:25:24Z

Phil:

== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 back wo bail.jpg

2012-07-09T18:23:39Z

Phil: Back of the thermometer with tilting bail removed.

== Summary ==
Back of the thermometer with tilting bail removed.
== Licensing ==
{{CC-BY-SA-3.0}}

File:Uni-t ut325 back battery.jpg

2012-07-09T18:20:45Z

Phil: Back side of UT325 thermometer without tilting bail and with battery cover removed.

== Summary ==
Back side of UT325 thermometer without tilting bail and with battery cover removed.
== Licensing ==
{{CC-BY-SA-3.0}}