+0.5.3 (2019-12-11)
+------------------
+
+Note: This release does NOT change the libsigrokdecode public C API in
+incompatible ways. This means existing frontends should not require any
+changes. However, individual PDs and their output changed, which may
+require some adaptations on the user's side in some cases.
+
+ * New supported protocol decoders:
+ - lin Local Interconnect Network (LIN) protocol
+ - x2444m Xicor X2444M/P nonvolatile static RAM protocol
+ - ds2408 1-Wire 8-channel addressable switch
+ - cc1101 Low-power sub-1GHz RF transceiver chip
+ - enc28j60 Microchip ENC28J60 10Base-T Ethernet controller protocol
+ - pca9571 NXP PCA9571 8-bit I²C output expander
+ - seven_segment 7-segment display protocol
+ - amulet_ascii Amulet Technologies LCD controller ASCII protocol
+ - tdm_audio TDM multi-channel audio protocol
+ - signature Annotate signature of logic patterns
+ - nes_gamepad NES gamepad button states
+ - flexray Automotive network communications protocol
+ - ir_rc6 RC-6 infrared remote control protocol
+ - ieee488 IEEE-488 General Purpose Interface Bus (GPIB/HPIB or IEC)
+ - hdcp HDCP protocol over HDMI
+ * Add a mandatory 'tags' decoder metadata field that can be used by frontends
+ for grouping various PDs together by topic, e.g. "Sensor", "Audio", etc.
+ The full list of currently used tags is documented in the HACKING file.
+ * All decoders must implement a reset() method now. It should reset all
+ PD-internal state and will be called when the decoder is restarted from
+ scratch (by frontends) with new data.
+ * Fix various memory leaks and bad memory accesses (e.g. bug #1374).
+ * Build system: Add support for Python 3.8 (bug #1438).
+ * Various compiler warning fixes.
+ * Slightly more detailed and easier to read log messages in some places.
+ * Fix incorrect decoder 'output' metadata.
+ * Improve annotation row ordering in various PDs.
+ * ook:
+ - Fix two typos causing decode issues.
+ * uart:
+ - Add support for break condition detection.
+ - Add 'FRAME' Python output type that communicates frame validity.
+ - Add '[rx|tx]_packet_delimiter' options.
+ - Add '[rx|tx]_packet_len' options.
+ - Communicate periods of idle frames to stacked decoders.
+ - Add 'ignore' parity type, remove unsupported 'check_parity' option.
+ - Shorten/rename various decoder option names.
+ * spiflash:
+ - Add support for Winbond W25Q80DV and Atmel AT25xxx.
+ - Add support for the chip erase commands (CE, CE2).
+ - Add support for write enable state tracking.
+ - Remember write protection latch from status registers.
+ - Fix WRSR incorrectly using MISO for register decodes.
+ - Add "EEPROM" to descriptions to increase discoverability in UIs.
+ * i2s:
+ - Fix incorrect channel assignment.
+ - Fix usage of the incorrect edge for the data sampling.
+ * ds1307:
+ - Fix incorrect unit for frequencies above 1Hz.
+ - Fix incorrect AM/PM flag handling.
+ * ir_rc5:
+ - Fix an incorrect command value.
+ - Massively improve performance via proper self.wait() usage.
+ * onewire_network:
+ - Add support for the 'Resume ROM' command.
+ - Add a 'Disable Test Mode' command for DS2408.
+ * sdcard_spi:
+ - Add support for CMD24 including payload data (bug #1365).
+ - Fix duplicated 'End bit' annotation emission.
+ - Fix incorrect handling of CMD17 (bug #1377).
+ - Add "Card is busy" annotations for CMD24 (bug #1376).
+ * spi:
+ - Add support for "transfer" annotations.
+ * atsha204a:
+ - Add support for ATECC508A.
+ - Display OtherData parameter correctly when Verify command is executed
+ in Validate mode.
+ - Only call output_tx_bytes() when the bytes buffer is not empty.
+ * usb_request:
+ - Append OUT data only if it has been ACK'd.
+ - Always keep IN and OUT transfers separate. In case the transfer is an
+ IN transfer, set the high bit as used in the endpoint descriptors (i.e.
+ 0x81 is IN enpoint 1, 0x01 is OUT endpoint 1).
+ - Use separate annotation rows for IN, OUT and CONTROL (bug #1046).
+ - Allow configuration of BULK IN transfer display via an option.
+ * modbus:
+ - Make C->S and S->C configurable via options.
+ - Add a 'framegap' option.
+ * mrf24j40:
+ - Add RX/TX frame annotations.
+ - Add TX retries/fails and CCAFAIL support.
+ * eeprom93xx:
+ - Add ASCII format support.
+ - Add OUTPUT_BINARY support.
+ * can:
+ - Add CAN-FD support.
+ - Add new 'fast_bitrate' option.
+ - More robust sample point position for low sample rates.
+ * gpib, iec:
+ - Removed in favor of the new ieee488 decoder.
+ * ir_nec:
+ - Fix decoder when running it multiple times (bug #1243).
+
0.5.2 (2018-09-12)
------------------
projects / libsigrokdecode.git / commitdiff