These can be extracted from the vendor's Windows drivers using a tool
from our 'sigrok-util' repository/project.
+ - kingst-la2016: The Kingst LA series of logic analyzers needs MCU firmware
+ and FPGA netlists. The 'sigrok-util' repository contains a script to
+ extract these files from the vendor software.
+
- lecroy-logicstudio: The LeCroy LogicStudio requires FPGA bitstream files.
These can be extracted from the vendor's Windows software using a tool
from our 'sigrok-util' repository/project.
path may contain slashes
path and serno are "greedy" (span to the end of the spec)
- Bluetooth Classic and Bluetooth Low Energy (BLE):
- conn=bt/<conn>/<addr>
+ conn=bt/<conn>/<addr>[/param=value]
conn can be: rfcomm, ble122, nrf51, cc254x
addr can be "dense" or separated, bt/cc254x/0123456789ab or
bt/rfcomm/11-22-33-44-55-66 or bt/ble122/88:6b:12:34:56:78
from a string that separates fields by colon, e.g. in the "--driver
<name>:conn=<spec>" example, that is why the dense form and the use
of dashes for separation are supported)
+ additional parameter keywords can be: channel, handle_rx, handle_tx,
+ handle_cccd, value_cccd, mtu
Some of the drivers implement a default for the connection. Some of the
drivers can auto-detect USB connected devices.
$ sigrok-cli --driver uni-t-ut61e-ser:conn=/dev/ttyUSB0 ...
$ sigrok-cli --driver voltcraft-vc820-ser:conn=/dev/ttyS0 ...
-
-When using any of the UT-D04 USB/HID cables you have to use the respective
-driver _without_ the '-ser' drivername suffix (internally all of these models
-are handled by the 'uni-t-dmm' driver).
-
-You also need to specify the USB vendor/device IDs of the cable.
-Autodetection is not possible here, since various other products use the
-USB VID/PID of those cables too, and there is no way to distinguish them.
-
-Since the UT-D04 cables are USB based (but don't use a USB-to-serial chip)
-there is no need to specify a serial port via 'conn', of course.
-However, the user running the frontend does also need to have permissions
-to access the respective USB device (see above).
+ $ sigrok-cli --driver uni-t-ut61e-ser:conn=hid/cp2110
+
+Using any of the UT-D04 et al USB/HID cables can be done in two different
+ways: Use transparent serial over HID support in libsigrok, by giving the
+-ser driver a conn=hid/... serial port spec. This re-uses the 'serial-dmm'
+driver, results in better coverage of these code paths, and reduces
+maintenance overhead. Or by running non-ser drivers and passing USB
+specific connection details. When the driver _without_ the '-ser' suffix
+is used, the models are handled by the 'uni-t-dmm' driver. These duplicate
+drivers only exist for historical reasons, the redundancy may result in
+differences of behaviour between the two implementations. When in doubt,
+check if the '-ser' driver works for you.
+
+In the USB specific driver case you need to specify the cable's vendor
+and product IDs. Autodetection is not possible here, since various other
+products use the USB VID/PID of those cables too, and there is no way to
+distinguish them. The sigrok software errs on the safe side, and won't
+communicate to serial ports unless explicitly instructed by the user.
+
+The user running the frontend does also need to have permissions to
+access the respective USB device (see above).
Examples (sigrok-cli):
done
+UNI-T UT-D04 cable issue on Windows
+-----------------------------------
+
+There have been reports that CH9325 based cables are not detected on
+Windows out of the box when they are assigned to libwdi drivers. Though
+they may be usable in that case when the USB address is manually specified.
+This can happen when some "USB to serial" driver is assigned which does not
+provide a genuine COM port that enumerates naturally. Manually assigning a
+"USB input device" driver can improve HIDAPI compatibility and make the
+cable show up in sigrok's serial port enumeration.
+
+
Enabling multimeter / data logger measurement output
----------------------------------------------------
projects / libsigrok.git / blobdiff