X-Git-Url: https://sigrok.org/gitweb/?a=blobdiff_plain;f=libsigrok.h;h=e43338e52dc0561985e5fb3ccc6a93643c55d472;hb=a4eb4b296da9818ffb04bb8023d43f6a006a81ca;hp=caa13757c32a9923976524a840c19cf64e025f1e;hpb=32c426d204e6133b19db486504beffd33a6f6548;p=libsigrok.git

diff --git a/libsigrok.h b/libsigrok.h
index caa13757..e43338e5 100644
--- a/libsigrok.h
+++ b/libsigrok.h
@@ -145,6 +145,7 @@ enum {
 	SR_T_KEYVALUE,
 	SR_T_UINT64_RANGE,
 	SR_T_DOUBLE_RANGE,
+	SR_T_INT32,
 };
 
 /** Value for sr_datafeed_packet.type. */
@@ -682,6 +683,9 @@ enum {
 	/** The device can demodulate signals. */
 	SR_CONF_DEMODULATOR,
 
+	/** Programmable power supply. */
+	SR_CONF_POWER_SUPPLY,
+
 	/*--- Driver scan options -------------------------------------------*/
 
 	/**
@@ -785,7 +789,7 @@ enum {
 	/** Logic low-high threshold range. */
 	SR_CONF_VOLTAGE_THRESHOLD,
 
-	/** The device supports using a external clock. */
+	/** The device supports using an external clock. */
 	SR_CONF_EXTERNAL_CLOCK,
 
 	/**
@@ -794,11 +798,41 @@ enum {
 	 */
 	SR_CONF_SWAP,
 
-        /** Center frequency.
-         * The input signal is downmixed by this frequency before the ADC
-         * anti-aliasing filter.
-         */
-        SR_CONF_CENTER_FREQUENCY,
+	/** Center frequency.
+	 * The input signal is downmixed by this frequency before the ADC
+	 * anti-aliasing filter.
+	 */
+	SR_CONF_CENTER_FREQUENCY,
+
+	/** The device supports setting the number of logic probes. */
+	SR_CONF_NUM_LOGIC_PROBES,
+
+	/** The device supports setting the number of analog probes. */
+	SR_CONF_NUM_ANALOG_PROBES,
+
+	/** Output voltage. */
+	SR_CONF_OUTPUT_VOLTAGE,
+
+	/** Maximum output voltage. */
+	SR_CONF_OUTPUT_VOLTAGE_MAX,
+
+	/** Output current. */
+	SR_CONF_OUTPUT_CURRENT,
+
+	/** Maximum output current. */
+	SR_CONF_OUTPUT_CURRENT_MAX,
+
+	/** Enabling/disabling output. */
+	SR_CONF_OUTPUT_ENABLED,
+
+	/** Channel output configuration. */
+	SR_CONF_OUTPUT_CHANNEL,
+
+	/** Over-voltage protection (OVP) */
+	SR_CONF_OVER_VOLTAGE_PROTECTION,
+
+	/** Over-current protection (OCP) */
+	SR_CONF_OVER_CURRENT_PROTECTION,
 
 	/*--- Special stuff -------------------------------------------------*/
 
@@ -817,13 +851,11 @@ enum {
 	/** The device supports specifying the capturefile unit size. */
 	SR_CONF_CAPTURE_UNITSIZE,
 
-	/** The device supports setting the number of probes. */
-	SR_CONF_CAPTURE_NUM_PROBES,
-
 	/** Power off the device. */
 	SR_CONF_POWER_OFF,
 
-	/** Data source for acquisition. If not present, acquisition from
+	/**
+	 * Data source for acquisition. If not present, acquisition from
 	 * the device is always "live", i.e. acquisition starts when the
 	 * frontend asks and the results are sent out as soon as possible.
 	 *
@@ -832,9 +864,22 @@ enum {
 	 * there is a choice. sr_config_list() returns those choices.
 	 *
 	 * In any case if a device has live acquisition capabilities, it
-	 * is always the default. */
+	 * is always the default.
+	 */
 	SR_CONF_DATA_SOURCE,
 
+	/**
+	 * On devices without sample compression (or compression turned off),
+	 * this returns the maximum number of samples that can be stored. This
+	 * can change as probes are disabled, depending on the hardware, so
+	 * should be queried after such changes are made. If not applicable,
+	 * fetching this value with sr_config_get() will return SR_ERR_NA.
+	 *
+	 * SR_CONF_LIMIT_SAMPLES should not be set to a higher value than
+	 * this value, if applicable.
+	 */
+	SR_CONF_MAX_UNCOMPRESSED_SAMPLES,
+
 	/*--- Acquisition modes ---------------------------------------------*/
 
 	/**