Difference between revisions of "Robomotic BugLogic 3"

From sigrok
Jump to navigation Jump to search
m
(5 intermediate revisions by 3 users not shown)
Line 1: Line 1:
{{Infobox logic analyzer
| image            = [[File:Robomotic_buglogic3.png|180px]]
| name            = Robomotic BugLogic 3
| status          = supported
| source_code_dir  = fx2lafw
| channels        = 8
| samplerate      = 24MHz
| samplerate_state = —
| triggers        = none (SW-only)
| voltages        = -0.5V — 5.25V
| threshold        = Fixed: VIH=2.0V—5.25V, VIL=-0.5V—0.8V
| memory          = none
| compression      = none
| website          = [http://norduino.robomotic.com/products-page/categories/buglogic3/ robomotic.com]
}}


[[File:Robomotic_buglogic3.jpg|thumb|right|Robomotic BugLogic 3]]
The '''Robomotic BugLogic 3''' is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.


The [http://norduino.robomotic.com/products-page/categories/buglogic3/ Robomotic BugLogic 3] is a cheap Cypress FX2-based 8-channel USB logic analyzer with a maximum samplerate of 24 MHz.
It is a clone of the [[Saleae Logic]].


See [[Robomotic BugLogic 3/Info]] for more detailed information on the device.
In sigrok, we use the open-source [[fx2lafw]] firmware for this logic analyzer.
 
See [[Robomotic BugLogic 3/Info]] for more details (such as '''lsusb -vvv''' output) about the device.


== Hardware ==
== Hardware ==


* TODO
* '''Main chip:''' Cypress CY7C68013A-56LFXC (FX2LP)
* '''I2C EEPROM''': ?
* '''Octal tristate bus transceiver''': LVC245 (TODO: vendor?)
* '''Crystal''': 24MHz


== More photos ==
== Photos ==


<gallery>
<gallery>
File:Buglogic3.jpg
File:Robomotic_buglogic3.jpg|<small>Device, front</small>
</gallery>
</gallery>
== Protocol ==
Since we use the open-source [[fx2lafw]] firmware for this device, we don't need to know the protocol.
== Resources ==
* [http://www.norduino.org/index.php?title=BugLogic3_board Buglogic3 wiki page]
* [http://norduino.robomotic.com/products-page/categories/buglogic3/ robomotic.com: Hardware description]
[[Category:Device]]
[[Category:Logic analyzer]]
[[Category:Supported]]

Revision as of 12:23, 28 July 2013

Robomotic BugLogic 3
Robomotic buglogic3.png
Status supported
Source code fx2lafw
Channels 8
Samplerate 24MHz
Samplerate (state)
Triggers none (SW-only)
Min/max voltage -0.5V — 5.25V
Threshold voltage Fixed: VIH=2.0V—5.25V, VIL=-0.5V—0.8V
Memory none
Compression none
Website robomotic.com

The Robomotic BugLogic 3 is a USB-based, 8-channel logic analyzer with up to 24MHz sampling rate.

It is a clone of the Saleae Logic.

In sigrok, we use the open-source fx2lafw firmware for this logic analyzer.

See Robomotic BugLogic 3/Info for more details (such as lsusb -vvv output) about the device.

Hardware

  • Main chip: Cypress CY7C68013A-56LFXC (FX2LP)
  • I2C EEPROM: ?
  • Octal tristate bus transceiver: LVC245 (TODO: vendor?)
  • Crystal: 24MHz

Photos

Protocol

Since we use the open-source fx2lafw firmware for this device, we don't need to know the protocol.

Resources