Difference between revisions of "Mcupro Logic16 clone"
Jump to navigation
Jump to search
m (→Hardware) |
(Add MCUPRO16 variant with Cyclone FPGA) |
||
| Line 31: | Line 31: | ||
* '''Crystal:''' 24.000MHz | * '''Crystal:''' 24.000MHz | ||
== Photos == | == Hardware (Cylone variant) == | ||
* '''FPGA''': [https://www.altera.com/products/fpga/cyclone-series/cyclone/support.html#Cyclone-Device-Handbook--All-Sections- Altera Cyclone EP1C3T100] | |||
* '''USB interface chip''': [http://www.cypress.com/?docID=45142 Cypress CY7C68013A] | |||
* '''I2C EEPROM''': [http://www.atmel.com/Images/doc3256.pdf Atmel 24C02N] | |||
* '''3.3V voltage regulator''': [http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf Advanced Monolithic Systems AMS1117-3.3] | |||
* '''1.5V voltage regulator''': [http://ams-semitech.com/attachments/File/AMS1117_20120314.pdf Advanced Monolithic Systems AMS1117-1.5] | |||
* '''Crystal (FX2):''' 24.000MHz | |||
* '''Crystal (FPGA):''' 100.000MHz | |||
* '''FPGA Bitstream''' 25P10 1MBit SPI NOR flash, ST Microelectronics | |||
* '''Bootstrap Controller''' STCMCU 15F10, 8051 compatible | |||
== Photos (Actel) == | |||
<gallery> | <gallery> | ||
| Line 39: | Line 52: | ||
File:Mcupro_Logic16_bottom.jpeg|<small>PCB, bottom</small> | File:Mcupro_Logic16_bottom.jpeg|<small>PCB, bottom</small> | ||
</gallery> | </gallery> | ||
== Photos (Cyclone) == | |||
<gallery> | |||
File:Mcupro_Logic16_case_top.jpeg|<small>Device, top</small> | |||
File:Mcupro_Logic16_case_bottom.jpeg|<small>Device, bottom</small> | |||
File:Mcupro Logic16 Variant2 top.jpg|<small>PCB with Altera Cyclone, top</small> | |||
File:IMG 0207 v1.JPG|<small>PCB with Altera Cyclone, bottom</small> | |||
File:Mcupro Logic16 Variant2 top flash+uC.jpg|<small>PCB, top, 1MBit flash and STCMCU uC</small> | |||
</gallery> | |||
== Protocol == | == Protocol == | ||
| Line 46: | Line 70: | ||
== Firmware == | == Firmware == | ||
This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate. | ;Alcatel variant | ||
: This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate. | |||
;Cyclone variant | |||
: This logic analyzer works with unmodified Saleae software. The PCB contains a serial flash chip, so it only requires an upload of Cypress FX2LP firmware in order to operate. | |||
The firmware extraction steps are identical to [[Saleae_Logic16#Firmware|steps for Saleae Logic16]], however you only need to have '''saleae-logic16-fx2.fw''' installed. | The firmware extraction steps are identical to [[Saleae_Logic16#Firmware|steps for Saleae Logic16]], however you only need to have '''saleae-logic16-fx2.fw''' installed. | ||
Revision as of 01:00, 5 May 2015
 | |
| Status | supported |
|---|---|
| Source code | saleae-logic16 |
| Channels | 3/6/9/16 |
| Samplerate | 100/50/32/16MHz |
| Samplerate (state) | — |
| Triggers | none (SW-only) |
| Min/max voltage | -0.9V — 6V |
| Threshold voltage | 1.5V (operates with 3.3V logic) |
| Memory | none |
| Compression | yes |
| Website | aliexpress.com |
The mcupro Logic16 clone is a USB-based, 16-channel logic analyzer with 100/50/32/16MHz sampling rate (at 3/6/9/16 enabled channels).
This is a clone of the Saleae Logic16.
See mcupro Logic16 clone/Info for more details (such as lsusb -v output) about the device.
Hardware (Actel variant)
- FPGA: Actel A3P125
- USB interface chip: Cypress CY7C68013A
- I2C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal: 24.000MHz
Hardware (Cylone variant)
- FPGA: Altera Cyclone EP1C3T100
- USB interface chip: Cypress CY7C68013A
- I2C EEPROM: Atmel 24C02N
- 3.3V voltage regulator: Advanced Monolithic Systems AMS1117-3.3
- 1.5V voltage regulator: Advanced Monolithic Systems AMS1117-1.5
- Crystal (FX2): 24.000MHz
- Crystal (FPGA): 100.000MHz
- FPGA Bitstream 25P10 1MBit SPI NOR flash, ST Microelectronics
- Bootstrap Controller STCMCU 15F10, 8051 compatible
Photos (Actel)
Device, top
Device, bottom
PCB, top
PCB, bottom
Photos (Cyclone)
Device, top
Device, bottom
PCB with Altera Cyclone, top
PCB with Altera Cyclone, bottom
PCB, top, 1MBit flash and STCMCU uC
Protocol
Firmware
- Alcatel variant
- This logic analyzer works with unmodified Saleae software. The Actel FPGA has on-chip flash storage, so it only requires an upload of Cypress FX2LP firmware in order to operate.
- Cyclone variant
- This logic analyzer works with unmodified Saleae software. The PCB contains a serial flash chip, so it only requires an upload of Cypress FX2LP firmware in order to operate.
The firmware extraction steps are identical to steps for Saleae Logic16, however you only need to have saleae-logic16-fx2.fw installed.